Portwell ROBO-8773VG Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 69

Portwell ROBO-8773VG Скачать руководство пользователя страница 66

Troubleshooting

ROBO-8773VG User’s Manual

5-6

Installation Problem
Question: How do I connect my keyboard and mouse, as there is only one

connector?

Answer:

Users may always adopt PS/2 keyboard and mouse over the PS/2 interface
(through Y-cable), J33 on ROBO-8773VG.

However, it is also fine to adopt a standard keyboard over the standard
keyboard connector on backplane, if provided. In this way, users need to
adopt a 5-pin keyboard connection cable to line-up, external keyboard
interface, J33 on ROBO-8773VG with the 10-pin keyboard connector on
backplane.

Question: After done with installation of SATA hard disk device, why does

system BIOS show nothing on screen?

Answer:

As matter of fact, you need to access system BIOS to enable SATA device.
(Please refer to SATA hard disk device installation guide)

Question: I am using an ATA-66 (or 100) hard drive, how can I know that ATA-66

function is enabled?

Answer:

You need to use the 80-pin ATA-66 IDE flat cable to have this function.

During the Post stage, you can see ATA-66 (or 100) message while hard
drive is being detected. Besides, After successfully installing Microsoft
series OS, you also need to install ATA-66/100 driver to active ATA-
66/100 function.

Information & Support
Question: I have one IDE hard disk and one SATA hard disk. How can I assign

SATA hard disk as First boot device?

Answer:

After entering system BIOS, access Advanced BIOS Feature. And then
press enter on Hard disk boot Priority. You will see the mode of your
SATA hard disk. Select it as first boot device.

Besides, please also notice. Every time, when your hard disk devices
have been changed, system bios will ask you to re-setup Hard disk boot
priority.

«
...
64
65
66
67
68
...
»

Содержание ROBO-8773VG






































































Отзывы:

Нет отзывов