Portek FlexiSharp Скачать руководство пользователя

Страница: 20 / 20

Portek Ltd.

Bryn Hall, Knolton Bryn

Overton-on-Dee

Wrexham, LL13 0LF

Tel: 01234 889 454

Fax: 01234 889 464

General enquiries

Email: [email protected]

EC Declaration of Conformity

Portek Ltd, Bryn Hall, Knolton Bryn, Overton on Dee,Wrexham, LL13 0LF

declare that the machinery named below conforms to the requirements of

EC Council Machinery Directive, Annex II

Designation of Machinery: Portek Chainsaw Sharpener

Relevant EC Council Directives:

2006/42/EC (Machinery Directive)

2014/30/EU (Electromagnetic Compatibility Directive)

Applied Harmonised Standards:

BS EN ISO 12100:2010
BS EN 62841-3-4:2016

The unit complies with all applicable Essential Requirements of the Directives.

Signature of Manufacturer's Representative:

Declaration made by Steve Morris

Design Engineer on 02/07/2018.

Declaration of Conformity

Flexisharp instructions.indd 20

11/07/2018 13:24

Содержание FlexiSharp





















Результаты поиска

Содержание FlexiSharp

Отзывы:

Похожие инструкции для FlexiSharp

Бренды по названию

Популярные бренды

Portek FlexiSharp, Руководство оператора

Результаты поиска

Содержание FlexiSharp

Отзывы:

Похожие инструкции для FlexiSharp

Бренды по названию

Популярные бренды