Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 77

Страница: 77 / 120

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

ELECTRICS | Intelligent Color Display (ICD)

Display Page: “RACE“ (Main Page)

►

This display page is displayed as the default page. Vehicle

relevant information (vital signs),

current operating conditions (gear display, speed) and performance

relevant information (lap

time) are displayed.

❶

❷

❸

❹

❺

❻

❶

In the upper area of the ICD are the eight shift lights in the housing and a corresponding col-

oured speed band on the screen. The settings of the shift lights/rev range correspond to

those of the 911 GT3 Cup Gen. II

❷

The displays for engine speed, engaged gear, and vehicle speed are shown in km/h in the

centre of the main page.

❸

In the left area of the RACE main page, the driver is shown the most important vehicle vital

signs.

❹

Compared to the RACE and QUALI pages of the 911 GT3 Cup Gen. II, the 911 GT3 Cup MR

Gen. II shows the status display of the TPM system and the status displays for the traction

control (optional) and the ABS.

Traction Control TC:

Display TC OFF = Switch Position 0

Display 1

11 = Control levels of TC (1 Min. to 11 Max. Control)

ABS

Display ABS OFF = Switch Position 0

❺

Status line for Alarm and Information messages.

❻

On the right side area of the RACE main page, the driver is shown information on the fuel

level, current lap time, current lap time difference to the best lap time driven so far or a set

reference lap.

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды