Porsche 911 GT3 Cup MR Gen. II Скачать руководство пользователя страница 32

Страница: 32 / 120

Version V2, 08/2020

Porsche 911 GT3 Cup MR Gen.II

Home

SUSPENSION | Brake Lines Quick Coupling

►

Optionally, the brake lines can be equipped with quick couplings. Especially in endurance races

(24h), this can save valuable time in the pit lane when the brakes have to be changed.

4.6 Brake Lines

Quick Couplings

NOTE

12 Nm

16 Nm

10 Nm

The specified tightening torques are mandatory.

WARNING

The quick coupling must always be checked for correct seating

(locking). If this is not observed, the brake pressure exerted by the

driver cannot be fully transferred to the pistons of the brake caliper,

whereby the driver assumes that the brake is fully functional (brake

pedal feedback).

DANGER

Never attempt to connect/disconnect the quick coupling while the

system is pressurized. This can result in damage to the connectors.

ATTENTION

Check the quick disconnect coupling components for damage and

leaks before every event and replace damaged/defective components

if necessary.

NOTE

When used properly, the quick coupling can be disconnected or

connected without fluid loss or air entry into the system. It is not ne-

cessary to bleed the brake system after disconnecting/connecting the

coupling. Ensure cleanliness when connecting the connectors. Failure

to observe can lead to leaks and damage to the quick connectors.

Содержание 911 GT3 Cup MR Gen. II

























































































































Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды

Porsche 911 GT3 Cup MR Gen. II, Техническое руководство

Результаты поиска

Содержание 911 GT3 Cup MR Gen. II

Отзывы:

Бренды по названию

Популярные бренды