background image

12

Replacing the Control Dial O-Rings 

 

Replacing Cap O-Ring 

 

Hold cap in front of you 

upside down with the o-ring 

groove facing up. Place one 

end of o-ring into cap groove 

at the point closest to you. 

Hold o-ring down with the 

thumb and index finger of  

one hand. 

 

Take hold of the far end of 

the o-ring with the thumb 

and index finger of the other 

hand. Roll o-ring slightly 

back towards you as you 

stretch the o-ring into the 

remainder of the cap 

groove.  

 

Lubricate o-ring often with 

silicone lubricant that came 

with your POOL FROG

® 

Cycler. DO NOT USE 

petroleum based lubricants. 

 

Replacing Knobs  

  

Back of Cycler 

 

Using a needle nose pliers, 

find the snap ring tail located 

at approximately the five 

o'clock position under the 

control dial.   

Pull down and out of the 

groove. 

 

Using a large screwdriver, 

loosen the control dial. 

Carefully pry the dial until it 

pulls out. 

 

Insert the non-lipped end of 

snap ring into the groove 

opening beginning at the 5 

o'clock position and push it 

up so that it threads itself 

around the control dial. 

Using a small screwdriver or 

pointed tool to help guide it, 

make sure the snap ring 

stays in the groove as it is 

inserted. 

 

Carefully replace the rubber 

o-ring without stretching it. 

Apply silicone lubricant, that 

came with your POOL 

FROG

® 

Cycler, on o-ring. 

 

Push control dial completely 

into the housing and turn the 

dial to setting 2. 

 

C O P Y 

C O P Y 

C O P Y 

      

COPY  

O T H E R C O P Y ? 

S I L I C O N E 

L U B R I C A N T 

Replace knob in back or on 

cap of POOL FROG

®

 Cycler 

by unscrewing old one and 

screwing in new one. 

 

Top of cap 

 

1. 

2. 

3. 

4. 

5. 

1. 

2. 

3. 

6. 

7. 

® 

 

R  

 

AN 

 

 

CYCLER 

POOL FROG® Cycler Maintenance

SILICONE

LUBRICANT

Содержание 5400 In-Line



















Отзывы: