PolyScience MX-CA11B страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 27

background image

110-511 PSC/EN

21

Technical Information

Performance Specifications

Operating Temperature Range:

A10° to 135°C

A20° to 275°F

Temperature Stability:

±0.07°C / ±0.13°F

Heater Wattage:

1100 watts

Electrical Requirements:

120V, 60Hz, 10 amps or

240V, 50Hz, 6 amps

Environmental Conditions

Indoor use only

Maximum Altitude:

2000 meter

Operating Ambient:

5° to 35°C (41° to 95°F)

Relative Humidity:

80%, non-condensing

Installation Category:

II

Pollution Degree:

2

Ingress Protection:

IP 31

Climate Class:

SN

Software Class:

B

Output Waveform:

Sinusoidal

Specifications subject to change without notice.

Attainable Temperatures:

Your MX Immersion Circulator can be used with reservoirs of various capacities and shapes as well as
different fluids. These variables may adversely affect temperature accuracy and stability. For example, a
reservoir with a large surface area loses heat more quickly, which may prevent the Circulator from
attaining the desired temperature.

[email protected]

www.

GlobalScientificSupply

.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

«
...
20
21
22
23
24
...
»

Содержание MX-CA11B




























Отзывы:

Нет отзывов

Похожие инструкции для MX-CA11B

Бренд: Ecco Страницы: 9

Бренд: Talet Equipment Страницы: 17

Бренд: Parata Страницы: 40

Бренд: B&G Страницы: 3

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: DBX Bushido Страницы: 12

Бренд: Garmin Страницы: 20

Бренд: Haaga Страницы: 31

Бренд: tayco Страницы: 111

Бренд: Laser Страницы: 2

Бренд: Lars Thrane Страницы: 50

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Raven Страницы: 48

Бренд: Pacific Страницы: 16

Бренд: GE Страницы: 176

Бренд: Triton Blue Страницы: 11

Бренд: Tieline Страницы: 359

Бренд: Ganter Norm Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды