PolyScience MX-CA11B Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 27

PolyScience MX-CA11B Скачать руководство пользователя страница 19

110-511 PSC/EN

18

Routine Maintenance and Troubleshooting

WARNING:

Always turn your Circulator OFF and disconnect it from the electrical power outlet before

performing any maintenance or service.

WARNING:

To avoid the potential for burns, allow the Immersion Circulator to cool completely before

cleaning or performing any maintenance.

WARNING:

Turn electrical power to the unit OFF and remove Immersion Circulator from reservoir

before draining. Always drain all fluid from the reservoir before moving or lifting. Be sure to follow
your organization’s procedures and practices regarding the safe lifting and relocation of heavy
objects.

CAUTION:

Always clean and dry your MX Immersion Circulator thoroughly before storing.

Maintaining Clear Bath Water

Optimum temperature and moisture conditions for algae growth existing when using water as a bath fluid.
To prevent algae contamination and minimize the frequency of draining the reservoir, an algaecide such
as polyclean Algaecide (004-300040) should be used.

WARNING:

Do not use chlorine bleach.

Cleaning Your Immersion Circulator

WARNING:

It is the user’s responsibility to properly decontaminate the unit in the event hazardous

materials are spilled on exterior or interior surfaces. Consult the manufacturer if there is any doubt
regarding the compatibility of decontamination or cleaning agents.

Temperature Controller

Turn the Temperature Controller OFF by pressing

and unplug power cord from the electrical outlet.

Remove Temperature Controller from bath reservoir and, keeping it upright, wipe the housing with a clean
cloth dampened with a mild detergent and water or mild all-purpose cleaner.

CAUTION:

Do not spray cleaning liquids directly onto the Temperature Controller or allow them to

enter the Controller’s vents. Do not use abrasives as these could scratch the housing or the digital
display.

CAUTION:

Never immerse the Circulator’s controls or display in water or other liquids or place under

running water. Do not clean the unit in a glassware washer.

[email protected]

www.

GlobalScientificSupply

.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

«
...
17
18
19
20
21
...
»

Содержание MX-CA11B




























Отзывы:

Нет отзывов