PolyScience MX-CA11B Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 27

PolyScience MX-CA11B Скачать руководство пользователя страница 11

110-511 PSC/EN

10

Normal Operation

Keys and Controls

Power

Turns the Immersion Circulator ON.

Menu

Accesses the Temperature Controller’s set-up sub-menus. The items in
these sub-menus are used to configure the Controller’s general
operational parameters (temperature unit, upper and lower temperature
limits, offset calibration, etc.).

Up Arrow

Used to increase temperature set point and other operational
settings/values.

Down Arrow

Used to decrease temperature set point and other operational
settings/values.

Turning Your Circulator ON

Press the

key.

All characters/symbols on the LCD will momentarily light. When the Circulator begins running, the actual
and set point temperatures will be displayed and the circulating symbol will be lit.

If the actual bath temperature is lower than the set point temperature, the heat symbol will also be lit.

Main Operational Display

Actual Bath
Temperature

Set Point
Temperature

Heating

Circulating

[email protected]

www.

GlobalScientificSupply

.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

«
...
9
10
11
12
13
...
»

Содержание MX-CA11B




























Отзывы:

Нет отзывов