Polycom ViewStation FX страница 167 Скачать руководство пользователя | Manualshive

Страница: 167 / 220

background image

Chapter 5

System Information and Diagnostics

©

Polycom, Inc.

153

ViewStation FX/VS 4000 User’s Guide

Pass-Thru Mode

In Pass-Thru Mode, the operational modes of both endpoints’
RS-232 ports depend on the port configuration of each endpoint.
Thus, two operational situations might arise:

•

Pass-Thru Mode to Pass-Thru Mode: Both endpoints are set to
Pass-Thru Mode.

•

Pass-Thru Mode to Control Mode: The near site is set to
Pass-Thru Mode and the far site is set to Control Mode.

The following table summarizes the port operation based on the
RS-232 mode configured by each endpoint.

The following information describes operational modes in more
detail.

Pass-Thru Mode to Pass-Thru Mode

—Two stations set to

Pass-Thru Mode behave essentially as a null-modem between their
respective externally connected devices. These two stations can be
two ViewStation FXs, two VS4000s, or one ViewStation FX and one
VS4000. The RS-232 port is used as a data channel over an H.320
video call. Data received from the RS-232 port on the near-end
ViewStation FX or VS4000 station is pushed through the call to the
far-end endpoint and then transmitted to the endpoint’s RS-232 port.
Similarly, data from the far-end endpoint is transmitted back to the
near-end ViewStation FX (through the H.320 call) and then
transmitted to the near-end RS-232 port.

The data channel speed is dynamically allocated. The maximum
data flow rate is based on the bandwidth of the call.

Near-Side Mode

Far-Side Mode

Resulting Operation

Control

N/A

Near-side CLI (Command Line
Interface)

Pass-Thru

Control

The near-side controls the CLI
of the far side

Pass-Thru

Pass-Thru

The data is passed in
full-duplex mode from the
near-side RS-232 port to the
far-side RS-232 port

«
...
165
166
167
168
169
...
»

Содержание ViewStation FX





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ViewStation FX

Бренд: Sven Страницы: 12

Бренд: Handicare Страницы: 56

Бренд: Samsung Страницы: 70

Бренд: Samsung Страницы: 21

Бренд: Samsung Страницы: 28

Бренд: 2N Страницы: 23

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 27

Бренд: 2N Страницы: 91

Бренд: EAW Страницы: 9

Бренд: Dickey-John Страницы: 109

Бренд: Intellitec Страницы: 16

Бренд: CLIMAVENETA Страницы: 23

Бренд: Ferguson Страницы: 13

Бренд: Magnavox Страницы: 25

Бренд: Valcom Страницы: 6

THOMSON DS120CD

Бренд: Bigben Страницы: 76

PELTOR ComTac 7

Бренд: 3M Страницы: 41

Бренд: RCA Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды