Poldent Endostar Provider Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 48

Poldent Endostar Provider Скачать руководство пользователя страница 40

39

Instructions for Use 2019-03-20

* Specifications may be changed without notice due to improvements.

Handpiece

Free Running Operation Speed

50 ±5 r/min to 1,000 ±100 r/min

Gear Ratio

1.9:1

Usable Burs

Type 1 (CA)

Rated Torque

Min. 0.04 N·m

Chuck Type

Push button latch type

Protection against Electric Shock

Internal powered ME equipment / Type BF applied part

Battery

Lithium ion battery (DC 3.7 V)

Dimensions

Approx. Dia. 28 mm × Length 196 mm
(including contra angle and motor handpiece)

Weight

Approx. 100 g
(including contra angle and motor handpiece)

Coupling Identification

Endostar Provider coupling

Applied Part

Contra angle, Motor handpiece

Battery Charger

Rated Input Voltage

A.C. 100 V – 240 V

Frequency

50 Hz / 60 Hz

Power Consumption

19 VA

Protection against Electric Shock

Class II / No applied part

Dimensions

Approx. Height 85 mm × Width 68 mm × Length 108 mm

Weight

Approx. 330 g

Name

Endostar Provider

Model

TR-CM

Degree of Protection (IEC 60529)

IPX0

Intended Use

The Endostar Provider is a compact and cordless endodontic treatment mo-
torized handpiece for preparation and enlargement of root canals. It can be
connected to the Endostar Navigator, an apex locator (sold separately). It can
be used to enlarge and prepare root canals, remove gutta-percha and softened
dentin, and perform professional mechanical tooth cleaning (PMTC).

Operating Principle

By electric drive, the Endostar Provider transmits motion, such as rotation and
vibration, to treatment instruments (dental files, reamers, etc.).

Essential Performance

None (There is no unacceptable risk.)

Technical Specifications

Specifications

«
...
38
39
40
41
42
...
»

Содержание Endostar Provider

















































Отзывы:

Нет отзывов