background image

SURVIVAL PREPARATION

For your safety, always ride in a group. Always tell someone where you're going 
and how long you expect to be gone. If it isn't possible to ride with others, and 
you must travel into remote areas, always carry survival equipment that's 
appropriate to the conditions you may encounter. Such equipment may include, 
but is not limited to: extra clothing, a sleeping bag, a flashlight, food and water, a 
signaling mirror, a means of building a fire, and a two-way radio or cellular 
telephone.

Always carry the owner’s manual on your snow bike. For added protection, 
purchase and carry the following items on your snow bike as well:

•  Extra Set of Spark Plugs

•  Tow Rope

•  Extra Oil

•  Fuel Deicer

•  Winter Survival Kit

•  Spare Drive Chain

•  Spare Chain Case Chain (if equipped)

•  Trail Map

•  First Aid Kit

•  Tool Kit

EXCESSIVE SPEED

WARNING

High speed driving, especially at night, could result in serious injury or death. 

Always reduce speed when driving at night or in inclement weather.

Always observe all state and local laws governing snow bike operation and 
speed limits. Always be alert and pay attention to the trail ahead. If your speed is 
40 MPH (64 km/h), your snow bike is traveling about 60 feet (18 m) per second. 
If you look back for only two seconds, your snow bike will travel about 120 feet 
(36 m). If your speed is 60 MPH (96 km/h), your snow bike will travel about 180 
feet (55 m) in two seconds.

Traveling at night requires extra caution. If your host bike is equipped with a 
headlight, check headlight and taillight to ensure proper operation, and don’t 
over-drive your headlight beam. Always be able to bring your snow bike to a 
stop in the distance illuminated by the headlight.

11

SAFETY

Содержание Timbersled ST 93 RIPPER 2019





















































































Отзывы: