manualshive.com logo in svg

Polaris SUPERSPORT 2006, Руководство пользователя

Polaris SUPERSPORT 2006 - высококачественный спортивный гидроскутер с максимальной производительностью. Для того чтобы ознакомиться с руководством по эксплуатации, скачайте бесплатное руководство на manualshive.com. Узнайте все возможности этого судна, загрузите инструкцию прямо сейчас!

Поделиться
Скачать
background image

13.5

ELECTRICAL

BATTERY

PREPARING A NEW BATTERY FOR 
SERVICE

To ensure maximum service life and performance from a 
battery, it must have proper initial servicing. To service a new 
battery, the following steps must be taken.

NOTE:  Do not service the battery unless it will be 
put into regular service within 30 days.

1.

Remove vent plug from vent fitting.

2.

Fill battery with electrolyte to the upper level marks on the
case.

3.

Set battery aside and allow it to cool and stabilize for 30
minutes.

4.

Add electrolyte to bring the level back to the upper level
mark on the case.

NOTE:  This is the last time that electrolyte should 
be added. If the level becomes low after this point, 
add only distilled water.

5.

Charge battery at 1/10 of its amp/hour rating. Example:1/
10 of 9 amp battery =.9 amps, 1/10 of 14 amp battery = 1.4
amps, 1/10 of 18 amp battery = 1.8 amps (recommended
charging rates).

6.

Check specific gravity of each cell with a hydrometer to
ensure each has a reading of 1.270 or higher.

BATTERY TESTING

There are three easy tests which can determine battery 
condition. Whenever the complaint is related to either the 
starting or charging systems, the battery should be checked 
first. Lead-acid batteries should be kept at or as near full 
charge as possible. If the battery is stored or used in a partially 
charged condition, hard crystal sulfation will form on the 
plates, reducing their efficiency and possibly ruining the 
battery.

OPEN CIRCUIT VOLTAGE TESTING (OCV)

Battery voltage should be checked with a digital multitester. 
Readings of 12.6v or less require further battery testing and 
charging.

SPECIFIC GRAVITY TEST

A tool such as the battery hydrometer (PN 2870836) can be 
used to measure electrolyte strength or specific gravity. As the 
battery goes through the charge/discharge cycle, the 
electrolyte goes from a heavy, more acidic state at full charge 
to a light, more water state when discharged. The hydrometer 

can measure state of charge and differences between cells in a 
multi-cell battery. Readings of 1.270 or greater should be 
observed in a fully charged battery. Differences of more 
than.025 between the lowest and highest cell readings indicate 
a need to replace the battery.

LOAD TEST

NOTE:  This test can only be performed on machines 
equipped with electric start. This test cannot be 
performed if the engine or starting system is not 
working properly.

A battery may indicate a fully charge condition on the OCV 
test and the specific gravity test, but still not have the storage 
capacity necessary to properly function in the electrical 
system. For this reason, a battery capacity or load test should 
be conducted whenever poor battery performance is 
encountered.

To perform the test, hook a multitester to the battery in the 
same manner as in the OCV test. The reading should be 12.6 
volts or greater. Engage the electric starter and view the 
registered battery voltage while cranking the engine. Continue 
the test for 15 seconds. During this cranking period, the 
observed voltage should not drop below 9.5 volts. If the 
beginning voltage is 12.6 or higher and the cranking voltage 
drops below 9.5 volts during the test, replace the battery.

REFILLING A LOW BATTERY

The normal charge/discharge cycle of a battery causes the cells 
to give off gases. These gases, hydrogen and oxygen, are the 

Table 13-2: Battery Voltage

STATE OF CHARGE

CONVENTIONAL 

LEAD-ACID

YUMACRON TYPE

100% CHARGED

12.60v

12.70v

75% CHARGED

12.40v

12.50v

50% CHARGED

12.10v

12.20v

25% CHARGED

11.90v

12.00v

0% CHARGED

< 11.80v

< 11.90v

Battery voltage per cell

100% CHARGED

1.265v

1.275v

75% CHARGED

1.210v

1.225v

50% CHARGED

1.160v

1.175v

25% CHARGED

1.120v

1.135v

0% CHARGED

< 1.100v

< 1.115v

Содержание SUPERSPORT 2006













































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SUPERSPORT 2006

Polaris 2005 Ranger 4x4 Owner'S Manual For Maintenance And Safety preview
2005 Ranger 4x4
Бренд: Polaris Страницы: 121
Hamron 008041 Operating Instructions Manual preview
008041
Бренд: Hamron Страницы: 12
Bad Boy 2013 RECOIL iS Owner'S Manual preview
2013 RECOIL iS
Бренд: Bad Boy Страницы: 56
Can-Am 2010 DPS Technical Manual preview
2010 DPS
Бренд: Can-Am Страницы: 58
SXT SCOTEX SPIKE Manual preview
SCOTEX SPIKE
Бренд: SXT Страницы: 40
Ardisam TX163 Operator'S Manual preview
TX163
Бренд: Ardisam Страницы: 10
Lyda 203D Owner'S Manual preview
203D
Бренд: Lyda Страницы: 55
Can-Am DS 450 Series Operator'S Manual preview
DS 450 Series
Бренд: Can-Am Страницы: 160
TOMCAR TM2 Owner'S Manual preview
TM2
Бренд: TOMCAR Страницы: 106
Jacobsen Turf Cat 628 ROPS Operator'S Manual preview
Turf Cat 628 ROPS
Бренд: Jacobsen Страницы: 9
Jayco 2012 OCTANE SUPER LITE Owner'S Manual preview
2012 OCTANE SUPER LITE
Бренд: Jayco Страницы: 101
Zhejiang Xinyang XY300 Operating Instruction preview
XY300
Бренд: Zhejiang Xinyang Страницы: 37
GAS GAS WILD HP 450 - 2005 Service Manual preview
WILD HP 450 - 2005
Бренд: GAS GAS Страницы: 71
FEISHEN FAAT6000 Owner'S Manual preview
FAAT6000
Бренд: FEISHEN Страницы: 116
Yamaha BADGER YFM80N Owner'S Manual preview
BADGER YFM80N
Бренд: Yamaha Страницы: 141
DFK INTIMIDATOR XD 4 Installation Instructions Manual preview
INTIMIDATOR XD 4
Бренд: DFK Страницы: 84
Razor DIRT QUAD SPORT Manual preview
DIRT QUAD SPORT
Бренд: Razor Страницы: 36
ParCar Gasoline Service Manual preview
Gasoline
Бренд: ParCar Страницы: 114

Бренды по названию

Популярные бренды

Загрузить еще бренды