manualshive.com logo in svg

Polaris SUPERSPORT 2006, Руководство пользователя

Polaris SUPERSPORT 2006 - высококачественный спортивный гидроскутер с максимальной производительностью. Для того чтобы ознакомиться с руководством по эксплуатации, скачайте бесплатное руководство на manualshive.com. Узнайте все возможности этого судна, загрузите инструкцию прямо сейчас!

Поделиться
Скачать
background image

11.2

REAR SUSPENSION

REAR SUSPENSION 
SPECIFICATIONS

MOUNTING TORQUE SPECIFICATIONS

3/8

”

top shock mounting bolts........28-30 ft. lbs. (39 - 41 Nm)

3/8

”

suspension mounting bolts....35 - 40 ft. lbs. (49 - 55 Nm)

7/16

”

 suspension mounting bolts...55 - 60 ft. lbs. (76 - 83 Nm)

Shock rod bolts(do not over torque)*Shock rods must pivot 
freely after torquing...................................12 ft. lbs. (17 Nm)

REAR SUSPENSION 
OPERATION

OPERATION

The primary function of the rear suspension is to provide a 
comfortable ride in all types of riding conditions. It separates 
the rider from the ground, while allowing for complete vehicle 
control. The rear suspension also must provide weight transfer 
and maintain track tension.

The rear suspension has many adjustable features for fine 
tuning to achieve optimum comfort. The suspension can be 
adjusted to suit rider preference and deliver excellent 
performance for a given set of conditions. It should be noted, 
however, that suspension adjustments involve a compromise 
or trade off. A machine set up to perform well in the moguls 
would not suit the preference of a groomed trail rider.

WEIGHT TRANSFER

The shifting of weight from the skis to the track is called 
weight transfer. As engine torque is applied to the drive axle 
the torque is transferred to the track, pulling it forward. This 
energy also tries to pull the suspension forward. The front 
torque arm reacts to this force by pushing down on the front of 
the track, in effect applying more weight to the front of the 
track and reducing the weight on the skis. It is important to 
note that energy used to lift the front of the machine is not 
available to push the vehicle forward.

Changing the angle of the front torque arm changes the 
suspension's reaction to the force. Adjusting the length of the 
limiter strap will change the front torque arm angle. 
Shortening the strap limits the extension of the front of the 
suspension; reducing the angle of the torque arm and 
increasing ski pressure during acceleration. Lengthening the 
strap allows the front of the suspension to extend further; 

increasing the angle of the torque arm and decreasing ski 
pressure during acceleration. Limiter strap adjustment has a 
great affect on weight transfer. Limiter straps only affect 
acceleration. It is important to check track tension whenever 
limiter strap length is changed. 

Front track shock spring preload also affects weight transfer. 
A stiffer spring and/or more preload on the spring transfers 
more weight to the track. A softer spring and/or less preload 
keeps more weight on the skis. Keep your riding application 
in mind when choosing springs and setting spring preload. 
Soft springs/preload will increase ski pressure, but may 
bottom out. Stiff springs/preload will provide more track 
pressure (reduced ski pressure), but may result in a less 
comfortable ride

During acceleration, the rear of the suspension will compress 
and the IFS will extend, pivoting the machine about the front 
torque arm. Because of this pivoting effect, rear spring and 
spring preload also have some effect on weight transfer. Softer 
rear springs, or less preload, allow more weight transfer to the 
track and reduce ski pressure. Stiffer rear springs, or increased 
preload, allow less weight transfer to the track and increase ski 
pressure. The main function of the rear torque arm is to 
support the weight of the vehicle and rider, as well as to 
provide enough travel to absorb bumps and jumps.

Shock valving also has an effect on weight transfer. Refer to 
shock tuning information in this chapter. Scissor stops also 
affect weight transfer. See scissor stop information also in this 
chapter.

Rear Scissor blocks also have a big effect on weight transfer.

 

see “SCISSOR STOP ADJUSTMENTS” on page 11.4.

SUSPENSION COUPLING

On all Polaris snowmobile rear suspensions, there are two 
torque arms that control the movement of the rail beam. Prior 
to the advent of suspension coupling, these torque arms could 
move independently of each other. Rear suspension coupling 
links the movement of the front and rear torque arms to each 
other.

The front rear scissor stop (FRSS) couples the movement of 
the front torque arm with the rear torque arm and limits the 
amount of independence between the movement of the front 
torque arm and the rear torque arm.

When hitting a bump, the front torque arm starts to compress. 
The FRSS links that movement to the rear torque arm, causing 
it to compress and raise the rear suspension up as one, 
allowing the suspension to hit the bump only once and 

Содержание SUPERSPORT 2006













































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SUPERSPORT 2006

Suzuki LT-A450X Manual preview
LT-A450X
Бренд: Suzuki Страницы: 528
Snapper GC9520KWV Setup Manual preview
GC9520KWV
Бренд: Snapper Страницы: 6
Snapper 63337 Parts Manual preview
63337
Бренд: Snapper Страницы: 8
Snapper 7085632 Safety Instructions & Operator'S Manual preview
7085632
Бренд: Snapper Страницы: 36
Polaris Scrambler Service Manual preview
Scrambler
Бренд: Polaris Страницы: 109
Arctic Cat 2008 Prowler Owner'S Manual preview
2008 Prowler
Бренд: Arctic Cat Страницы: 84
Tomberlin Anvil Operator'S Manual preview
Anvil
Бренд: Tomberlin Страницы: 32
PRONAR T700M/1 Translation Of The Original Copy Of The Manual preview
T700M/1
Бренд: PRONAR Страницы: 166
Costway Honey Joy TY324116 User Manual preview
Honey Joy TY324116
Бренд: Costway Страницы: 7
Baja motorsports WD400U-2 Owner'S Manual preview
WD400U-2
Бренд: Baja motorsports Страницы: 89
Yamaha RS90RK Service Manual preview
RS90RK
Бренд: Yamaha Страницы: 841
CADDY 640t Assembly Instruction preview
640t
Бренд: CADDY Страницы: 2
CaddyStar XT User Manual preview
XT
Бренд: CaddyStar Страницы: 26
Cannondale 2002 Blaze Owner'S Manual preview
2002 Blaze
Бренд: Cannondale Страницы: 180
Honda FOURTRAX 350 4x4 2001 Owner'S Manual preview
FOURTRAX 350 4x4 2001
Бренд: Honda Страницы: 169
Honda 2005 TRX450R Owner'S Manual preview
2005 TRX450R
Бренд: Honda Страницы: 227
Honda 1990 TRX200 Fourtrax200 Owner'S Manual preview
1990 TRX200 Fourtrax200
Бренд: Honda Страницы: 149
Yamaha YFM 400 FWA P Service Manual preview
YFM 400 FWA P
Бренд: Yamaha Страницы: 41

Бренды по названию

Популярные бренды

Загрузить еще бренды