Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 52

Страница: 52 / 147

REAR SUSPENSION

1. Check rear shock absorber movement to ensure the correct amount of

suspension travel and ground clearance. Refer to the specifications section
beginning on page 121.

WARNING

Inadequate ground clearance could result in components contacting the

ground, causing loss of control and serious injury or death. Always ensure

ground clearance is at specification.

DRIVE BELT

1. Check the drive belt

teeth for stones or other debris.

2. Inspect drive belt condition. If you discover cracks, broken teeth or frayed

edges, replace the drive belt before riding. Refer to the

SLINGSHOT Service

Manual

, or an authorized dealer can assist.

PRE-RIDE INSPECTIONS

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды