Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 147

background image

CHANGING THE PASSCODE

The factory-set passcode is 0000. Enter this passcode at step 5 the first time
you change the passcode.

1. Unlock the security system. See page 46.

2. With the engine off and the park brake engaged, press and release the

MODE button repeatedly until “SECURE” displays in the gauge.

3. Press and hold the MODE button until “SETCODE” displays.

4. Press and hold the MODE button until “OldCodE” displays.

5. Enter your existing passcode using the same process used to unlock the

system.

6. If the passcode is not correct, “bAd COdE” displays. Re-enter the correct

passcode. If the passcode entered is correct, “NEWCodE” displays.

7. Enter your new passcode using the same process used to unlock the

system.

8. When “CONFIRM” displays, re-enter the new passcode to confirm.

9. If the two entries do not match, “bAd COdE” displays and you’ll be returned

to step 7. If the two entries match, “SUCCESS” displays. The passcode has
been changed.

10. Record your new passcode and keep it in a safe location.

Do not place your

4-digit passcode anywhere in the vehicle.

SECURITY LEVELS

The security system offers three security levels as outlined below:

SECURITY

LEVEL

ENGINE STARTING REQUIREMENTS

PASSIVE
(default
setting)

When set to PASSIVE, use of the ignition key is required. Manual entry of
your passcode is not required.

ACTIVE

When set to ACTIVE, you will be prompted to press the MODE button
within 10 seconds of turning the ignition switch off. The system will then
require manual entry of your passcode the next time the ignition switch is
turned on. See Unlocking the Security System. If you fail to press the
MODE button within the allotted time, the system will not require manual
entry of your passcode the next time the ignition switch is turned on.

AUTO

When set to AUTO, the system requires manual entry of your passcode
every time the ignition switch is turned on.

45

FEATURES AND CONTROLS

Downloaded from

«
...
45
46
47
48
49
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренд: Mazda Страницы: 4

Бренд: Wagan Страницы: 12

Бренд: kaarta Страницы: 29

Бренд: Mobis Страницы: 16

Бренд: Subaru Страницы: 216

BLADE-AL(TB)-TL2

Бренд: iDataLink Страницы: 9

Бренд: Magneti Marelli Страницы: 2

Бренд: BMW Страницы: 21

Бренд: NavLinkz Страницы: 21

Бренд: EUFAB Страницы: 16

Бренд: Cadillac Страницы: 352

Бренд: GReddy Страницы: 12

Бренд: TracRac Страницы: 8

Бренд: Nos Страницы: 22

Filtercharger 57-9004

Бренд: K&N Engineering Страницы: 4

Бренд: Honda Страницы: 219

Бренд: Metra Electronics Страницы: 17

Бренд: AA Products Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды