Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 147

background image

RIDE COMMAND™ BUTTONS

BUTTON

FUNCTION

Rider Screen Button

Press the Rider Screen button to access
the customizable split screen menu
system, access to ride data, vehicle
status, and vehicle information.

Navigation Button

Press the Navigation button to access
Ride Command™ navigation features (if
equipped), find directions, and look up
addresses, gas stations, and other points
of interest.

Bluetooth Button

Press the Bluetooth button to pair a
phone or headset to the Ride
Command™ display.

Power Button

Press the Display On/Off button to turn
the Ride Command™ display on and off
while motorcycle is in use.

Audio Button

Press the Audio Button to change the
audio source, and set radio presets.

Volume Decrease
Button

Press the Volume Decrease Button to
adjust the volume downward.

Volume Increase
Button

Press the Volume Increase Button to
adjust the volume upward.

RIDE COMMAND™ SETTINGS

The Settings Menu is where you can personalize your Navigation System. You
can configure settings, such as Language, Speed Units, Time Formats, as well
as audio and vehicle settings. The Settings Menu is composed of 4 categories
that allow you to customize your screens; General, Time, Audio, and Vehicle.

GENERAL

From the General settings menu you can do the following:.

•  Change the Language
•  Set the Speed Units (MPH or KPH)
•  Set the Temperature Units (F or C)

31

FEATURES AND CONTROLS

Downloaded from

«
...
31
32
33
34
35
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

01 29 9 416 497

Бренд: BMW Страницы: 5

Бренд: Toyota Страницы: 371

Бренд: Mazda Страницы: 13

Бренд: Inbay Страницы: 20

Бренд: Cadillac Страницы: 407

Бренд: Pyle Страницы: 2

JEEP GL ADIATOR JT TOPPER ROOF RACK

Бренд: JCROffroad Страницы: 7

IVH-9000-2R440Q

Бренд: Vecow Страницы: 110

Бренд: Saturn Страницы: 440

Бренд: Ford Страницы: 52

Бренд: true-i Страницы: 11

Бренд: Great day Страницы: 5

Бренд: Toyota Страницы: 204

Бренд: Kia Страницы: 417

Бренд: Ferrari Страницы: 45

Бренд: AdvanceTec Страницы: 8

Бренд: AdvanceTec Страницы: 12

Бренд: AdvanceTec Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды