Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 147

background image

HEADLIGHT HIGH/LOW BEAM SWITCH

The headlights are always on when the ignition switch is in the ON position. To
switch the headlights between low beam and high beam, tap the turn signal
lever forward, toward the steering wheel. The master lighting switch (Canada)
must be in the ON position to allow operation of the high beam headlights. See
page 23.

TURN SIGNAL LEVER

Before turning, activate a turn signal to alert others of your intentions. Check turn
signal lamps before each ride.

NOTE

The key must be in the ON position to activate the turn signals.

1. Move the turn signal lever downward to signal a left turn. The left turn signal

lamps at the front and rear of the vehicle will flash. The indicator arrows on
the console will flash when a turn signal or hazard signal is activated.

2. Move the lever upward to signal a right turn. The right signal lamps and

indicator will flash.

3. The turn signal automatically cancels and the lever returns to the center

position when the turn is completed.

CRUISE CONTROL SWITCHES

The cruise control switch

q

and set button

w

are located on the turn signal lever.

Before using the cruise control, read the safety and operation procedures. See
page 61.

22

FEATURES AND CONTROLS

Downloaded from

«
...
22
23
24
25
26
...
»

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренд: Camcar Страницы: 6

Бренд: Whispbar Страницы: 85

Бренд: hc-cargo Страницы: 60

Бренд: Honda Страницы: 4

SAFESTOP SS0005

Бренд: Pro-gard Страницы: 4

Бренд: Hummer Страницы: 502

Бренд: AddSecure Страницы: 14

Бренд: Ford Страницы: 8

Бренд: Intec Страницы: 16

Бренд: Cadillac Страницы: 20

FABIA II TMB PS 035

Бренд: Skoda Страницы: 16

Бренд: r.LiNK Страницы: 21

Бренд: Toyota Страницы: 672

PRIME DESIGN HRR3-E-PM52

Бренд: Safe Fleet Страницы: 12

Бренд: Easee Страницы: 21

Бренд: MiX Telematics Страницы: 39

2001 Accord Sedan

Бренд: Honda Страницы: 372

Бренд: Imiola HAK-POL Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды