Polaris RZR 570 2013 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

2.21

5.

Locate throttle cable on the left-hand side of the
throttle body. Slide back the cable adjuster boot.

6.

Using an open-end wrench, loosen the adjustment
jam nut (A) . Using another open-end wrench, move
the cable adjuster (B) until 1/16 to 1/8″ (1.5 - 3 mm)
of free play is achieved at the throttle pedal.

NOTE

While adjusting, lightly move the throttle pedal in and

out.

7.

Re-tighten the jam nut after final adjustment is made.

8.

Apply a small amount of grease to the inside of the
boot

u

and slide it over the cable adjuster to its

original position.

9.

Reinstall the cargo box access panel.

ENGINE AND PVT INTAKE PRE-FILTER
SERVICE

It is recommended that the engine and PVT intake pre-
filter be inspected daily. The filter should be inspected
using the following procedure:

NOTE

The engine and PVT intake pre-filter is located just

above the left-rear wheel fender.

1.

Press “IN” on the intake grill cover tabs

q

and

remove the pre-filter cover.

2.

Remove and inspect the pre-filters

w

. If necessary,

clean with soapy water and dry with compressed air.

3.

Reinstall the dry pre-filters and install the pre-filter
cover.

«
...
55
56
57
58
59
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: MANCO Страницы: 4

Бренд: UtilityDump Страницы: 13

Бренд: E-TON Страницы: 34

Бренд: Yamaha Страницы: 25

Бренд: Yamaha Страницы: 41

Бренд: Yamaha Страницы: 134

4x4 Timberwolf YFB250FWM

Бренд: Yamaha Страницы: 161

Бренд: Yamaha Страницы: 81

4X4 BIG BEAR YFM40FC

Бренд: Yamaha Страницы: 168

4X4 BIG BEAR PROFESSIONAL

Бренд: Yamaha Страницы: 172

2006 GRIZZLY 125

Бренд: Yamaha Страницы: 153

2012 Griizzly 700 YFM7FGPB

Бренд: Yamaha Страницы: 174

2004 Rhino 660 YXR660FAS

Бренд: Yamaha Страницы: 154

1998 BigBear 2x4 YFM350UK

Бренд: Yamaha Страницы: 168

2009 Raptor 250

Бренд: Yamaha Страницы: 293

2008 Raptor 250

Бренд: Yamaha Страницы: 311

Бренд: Yamaha Страницы: 382

Бренд: Yamaha Страницы: 375

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды