Polaris RZR 570 2013 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

2.19

FUEL SYSTEM AND AIR INTAKE

FUEL SYSTEM

WARNING

Gasoline is extremely flammable and explosive under

certain conditions.

Always stop the engine and refuel outdoors or in a well

ventilated area.

Do not smoke or allow open flames or sparks in or near

the area where refueling is performed or where

gasoline is stored.

Do not overfill the tank. Do not fill the tank neck.

If you get gasoline in your eyes or if you swallow

gasoline, seek medical attention immediately.

If you spill gasoline on your skin or clothing,

immediately wash it off with soap and water and

change clothing.

Never start the engine or let it run in an enclosed area.
Engine exhaust fumes are poisonous and can result in

loss of consciousness or death in a short time.

Never drain the fuel when the engine is hot. Severe

burns may result.

FUEL LINE

1.

Check the quick-connect fuel line

q

from the engine

fuel rail connection to the fuel tank connection for
signs of wear, deterioration, damage or leakage.
Replace if necessary.

2.

Be sure fuel line is routed and retained properly.

NOTE

Make sure line is not kinked or pinched.

3.

Replace fuel line every two years.

FUEL PUMP / FUEL FILTERS

The RZR 570 engine uses a serviceable, high-volume,
high-pressure, fuel pump that includes a preliminary filter
and an internal fine filter located before the pump
regulator.

NOTE

Neither filter is servicable individually. Must replace the

fuel pump as an assembly.

Refer to Chapter 4 for fuel pump replacement and all

other information related to the EFI System.

«
...
53
54
55
56
57
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: Snapper Страницы: 82

Бренд: TransTank Страницы: 28

Бренд: Access Страницы: 72

Black-Topper Shooter II

Бренд: Etnyre Страницы: 51

Black-Topper SHOOTER Series

Бренд: Etnyre Страницы: 84

Бренд: Can-Am Страницы: 152

Бренд: Landoll Страницы: 64

Бренд: EBO Страницы: 19

Бренд: Rato Страницы: 118

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 172

Бренд: FERPINTA Страницы: 14

Бренд: Land Pride Страницы: 96

Бренд: Wenger Страницы: 36

Бренд: Field Tuff Страницы: 8

Бренд: Aeon Страницы: 93

Бренд: Aeon Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды