Polaris RZR 570 2013 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

2.17

COOLANT LEVEL INSPECTION

The pressure cap

q

and recovery bottle

w

are located

under the front hood of the vehicle. The coolant level
must

be

maintained

between

the

minimum

and

maximum levels indicated on the recovery bottle.

With the engine at operating temperature, the coolant
level should be between the upper and lower marks on
the coolant recovery bottle. If not, perform the following
procedure:

1.

Position the vehicle on a level surface.

2.

Remove the hood from the front cab.

3.

View the coolant level in the recovery bottle.

4.

If the coolant level is below the MIN line, inspect the
coolant level in the radiator.

NOTE

If overheating is evident, allow system to cool

completely and check coolant level in the radiator and

inspect for signs of trapped air in system.

WARNING

Never remove the pressure cap when the engine is

warm or hot. Escaping steam can cause severe burns.

The engine must be cool before removing the pressure

cap.

5.

Remove the pressure cap. Using a funnel, add
coolant to the top of the filler neck.

6.

Reinstall the pressure cap.

NOTE

Use of a non-standard pressure cap will not allow the

recovery system to function properly.

7.

Remove recovery bottle cap and add coolant using a
funnel.

8.

Fill recovery bottle to MAX level with Polaris 50/50
Extended Life Anti Freeze/Coolant as required for
freeze protection in your area.

9.

Reinstall the recovery bottle cap.

10. If coolant was required, start engine and check for

leaks. Make sure radiator fins are clean to prevent
overheating.

COOLING SYSTEM PRESSURE TEST

Refer to Chapter 3 for cooling system pressure test
procedure.

COOLANT STRENGTH / TYPE

Test the strength of the coolant using an antifreeze
hydrometer.

• A 50/50 mixture of antifreeze and distilled water will

provide the optimum cooling, corrosion protection, and
antifreeze protection.

• Do not use tap water, straight antifreeze, or straight

water in the system. Tap water contains minerals and
impurities which build up in the system.

• Straight water or antifreeze may cause the system to

freeze, corrode, or overheat.

Polaris Premium Antifreeze

2871534 - Quart

2871323 - Gallon

«
...
51
52
53
54
55
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: MANCO Страницы: 57

Бренд: MANCO Страницы: 57

Бренд: Polaris Страницы: 3

Бренд: Lincoln Страницы: 2

Бренд: Knox Страницы: 46

Бренд: Leggero Страницы: 63

Бренд: E-TON Страницы: 35

Бренд: Kubota Страницы: 112

Бренд: Can-Am Страницы: 423

BurdenMaster B 2-00

Бренд: Taylor-Dunn Страницы: 266

Бренд: Ifor Williams Trailers Страницы: 16

Бренд: Suzuki Страницы: 50

Бренд: Pongratz Страницы: 11

Black-Topper BT-1 Distributors 2008

Бренд: Etnyre Страницы: 48

Black-Topper CENTENNIAL

Бренд: Etnyre Страницы: 53

Бренд: Marlon Страницы: 9

Бренд: Duruxx Страницы: 82

Бренд: Club Car Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды