Polaris RZR 570 2013 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

2.13

19. Re-check the oil level on the dipstick and add oil as

necessary to bring the level to the upper mark on the
dipstick.

20. Dispose of used oil and oil filter properly.

ENGINE BREATHER HOSE INSPECTION

The engine is equipped with a breather hose

q

. Inspect

the breather hose for possible kinks or wear. The hose is
form fitted for a proper fit. Follow the breather hose from
the engine crankcase to the air intake baffle box on the
left-hand rear fender panel.

NOTE

Make sure line is not kinked or pinched.

ENGINE AND TRANSMISSION MOUNTS

Periodically inspect engine and transmission mounts for
cracks or damage.

Refer to Chapter 3 “Engine Assembly and Installation” for
mounting fastener torque values.

COMPRESSION TEST SPECIFICATION

NOTE

This engine has decompression components.

A smooth idle generally indicates good compression.
Low engine compression is rarely a factor in running
condition problems above idle speed.

Cylinder Compression:

80 - 120 psi (decompression)

A leakdown test is a more accurate way to check for
engine wear. Even with compression in the acceptable
range, the engine may still have a worn cylinder/rings.

Cylinder Leakdown:

Less than 20%

«
...
47
48
49
50
51
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: MANCO Страницы: 57

Бренд: MANCO Страницы: 57

WorkHorse ST 480

Бренд: Ezgo Страницы: 164

Бренд: citEcar Страницы: 28

Бренд: Makita Страницы: 128

Бренд: Knox Страницы: 46

Бренд: Strongway Страницы: 16

Camoplast ATV T4S

Бренд: CAMSO Страницы: 10

Бренд: Can-Am Страницы: 147

Бренд: Hsun Страницы: 100

Бренд: Taylor-Dunn Страницы: 233

WARRIOR YFM350XNC

Бренд: Yamaha Страницы: 167

Бренд: ROSSO MOTORS Страницы: 16

Бренд: ROSSO MOTORS Страницы: 17

Бренд: ROSSO MOTORS Страницы: 18

Бренд: PLAYTIVE JUNIOR Страницы: 22

Бренд: ODES Страницы: 89

Бренд: Hisun Motors Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды