Polaris RZR 570 2013 Скачать руководство пользователя страница 456 | Manualshive

Страница: 456 / 482

background image

11.36

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

FAN CONTROL CIRCUIT OPERATION /
TESTING

Power is supplied to the fan via the Orange/Black wire
when the relay is ON. The ground path for the fan motor
is through the Brown harness wire. Refer to “RELAYS”
later in this chapter for more information on fan functions.

CAUTION

Keep hands away from fan blades during operation.

Serious personal injury could result.

NOTE

The fan may not function or operation may be delayed if

coolant level is low or if air is trapped in the cooling

system. Be sure cooling system is full and purged of air.

Refer to Chapter 2 “Maintenance” for cooling system

information.

FAN CONTROL CIRCUIT BYPASS TEST

1.

Disconnect

harness

from

coolant

temperature

sensor on the engine cylinder head (see Chapter 4 –
ECT Sensor Replacement, page

).

2.

With the transmission in Park, start the engine. After
a few seconds, the fan should start running and the
“Check Engine” indicator should display on the
instrument

cluster.

This

indicates

all

other

components are working properly.

3.

If the fan does not run or runs slowly, check the fan
motor

wiring,

ground,

motor

condition

and

mechanical relay for proper operation. Repair or
replace as necessary. If the fan runs with the sensor
harness disconnected, but will not turn on when the
engine is hot, check the coolant temperature sensor
and connector terminals.

COOLANT TEMPERATURE SENSOR

The coolant temperature sensor can be tested using an
ohmmeter or voltmeter.

1.

With the engine and temperature sensor at room
temperature (68°F = 20°C), disconnect the harness.

2.

With the meter in the ohms mode, place the meter
leads onto the sensor contacts.

3.

Use the table Temperature / Resistance table to
determine if the sensor needs to be replaced.

TEMPERATURE °F (°C)

RESISTANCE

68 °F (20 °C)

2.5 k Ω ± 6%

212 °F (100 °C)

186 ± Ω 2%

NOTE

If the coolant temperature sensor or circuit malfunctions

the radiator fan will default to 'ON'.

«
...
454
455
456
457
458
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: Honda Страницы: 29

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 93

Бренд: Yamaha Страницы: 99

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 114

Бренд: Yamaha Страницы: 112

Kodiak YFM400FWK

Бренд: Yamaha Страницы: 167

Бренд: Yamaha Страницы: 193

Kodiak YFM45FAV

Бренд: Yamaha Страницы: 194

KODIAK 700 YFM70KDXH

Бренд: Yamaha Страницы: 178

KODIAK 700 YFM70KDHG

Бренд: Yamaha Страницы: 180

KODIAK Ultramatic

Бренд: Yamaha Страницы: 185

KODIAK 4X4 Ultramatic

Бренд: Yamaha Страницы: 185

KODIAK 450 Ultramatic

Бренд: Yamaha Страницы: 189

GRIZZLY YFM70GPAH

Бренд: Yamaha Страницы: 174

Бренд: Yamaha Страницы: 190

KODIAK 400 Ultramatic 4x4

Бренд: Yamaha Страницы: 187

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды