Polaris RZR 570 2013 Скачать руководство пользователя страница 399 | Manualshive

Страница: 399 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

9.37

TROUBLESHOOTING

BRAKE NOISE TROUBLESHOOTING

Dirt or dust buildup on the brake pads and disc is the most common cause of brake noise (squeal caused by vibration).
If cleaning does not reduce the occurrence of brake noise, Permatex™

Disc Brake Quiet

can be applied to the back of

the pads. Follow directions on the package. This will keep pads in contact with caliper piston(s) to reduce the chance
of squeaks caused by dirt or dust.

BRAKE NOISE TROUBLESHOOTING

POSSIBLE CAUSE

REMEDY

Dirt, dust, or imbedded material on pads or disc

Spray disc and pads with CRC Brakeleen™ or an equivalent non-
flammable aerosol brake cleaner. Remove pads and/or disc hub to
clean imbedded material from disc or pads.

Pad(s) dragging on disc (noise or premature pad wear) because of
improper adjustment
Master cylinder reservoir overfilled
Master cylinder compensating port restricted
Master cylinder piston not returning completely
Caliper piston(s) not returning
Operator error (riding the brake)

Adjust pad stop (front calipers)

Set to proper level
Clean compensating port
Inspect. Repair as necessary
Clean piston(s) seal
Educate operator

Loose wheel hub or bearings

Check wheel and hub for abnormal movement.

Brake disc warped or excessively worn

Replace disc

Brake disc misaligned or loose

Inspect and repair as necessary

Noise is from other source (axle, hub, disc or wheel)

If noise does not change when brake is applied check other sources.
Inspect and repair as necessary

Wrong pad for conditions

Change to a softer or harder pad

BRAKES SQUEAL / POOR BRAKE
PERFORMANCE

• Air in system
• Water in system (brake fluid contaminated)
• Caliper or disc misaligned
• Caliper dirty or damaged
• Brake line damaged or lining ruptured
• Worn disc and/or friction pads
• Incorrectly adjusted stationary pad
• Worn or damaged master cylinder or components
• Damaged break pad noise insulator
• Brake pads dragging
• Brake caliper dragging

PEDAL VIBRATION

• Disc damaged
• Disc worn (runout or thickness variance exceeds serv-

ice limit)

CALIPER OVERHEATS (BRAKES DRAG)

• Compensating port plugged
• Pad clearance set incorrectly
• Brake pedal binding or unable to return fully
• Residue build up under caliper seals
• Operator riding brakes

BRAKES LOCK

• Alignment of caliper to disc
• Caliper pistons sticking
• Improper assembly of brake system components

«
...
397
398
399
400
401
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: Odes Industry Страницы: 73

Бренд: Arctic Cat Страницы: 174

ErgoSteer SP001V9810010

Бренд: FENDT Страницы: 40

Бренд: Yamaha Страницы: 134

Бренд: Yamaha Страницы: 206

Бренд: Seizmik Страницы: 10

Raider Classic 250

Бренд: Dazon Страницы: 98

Бренд: Can-Am Страницы: 401

Бренд: Kärcher Страницы: 346

Бренд: KAYO MOTO Страницы: 7

Бренд: KAYO MOTO Страницы: 186

WOLVERINE YXE70WPXH

Бренд: Yamaha Страницы: 186

Бренд: Yamaha Страницы: 193

Бренд: Taylor-Dunn Страницы: 204

Бренд: Kärcher Страницы: 19

1990 DS Gasoline Golf Car

Бренд: Club Car Страницы: 20

Бренд: Club Car Страницы: 44

Бренд: Yamaha Страницы: 194

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды