Polaris RZR 570 2013 Скачать руководство пользователя страница 375

Страница: 375 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

9.13

CALIPER REMOVAL

NOTE

Do not get oil, grease, or fluid on the parking brake

pads. Damage to or contamination of the pads may

cause the pads to function improperly.

Remove the clip pin and pin (A) from the parking
brake cable.

NOTE

Be sure the parking brake is not engaged.

Remove the two fasteners (B) retaining the parking
brake caliper mount / shift cable bracket.

Lift the parking brake caliper off the brake disc and
remove it from the vehicle.

CALIPER DISASSEMBLY / INSPECTION

NOTE

Refer to the “Electronic Parts Catalog” for parking brake

caliper replacement parts information.

Remove the two caliper assembly bolts (C).

Slide the brake pads and springs from the assembly.

NOTE

Retain the lever and ball bearings for reassembly.

Inspect brake pads for excessive wear. Replace as
needed.

Check the three steel balls for any signs of cracking.
Replace as needed.

Check ball seats in lever and stationary actuator. If
excessively worn, replace parts as needed.

BRAKE SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды