Polaris RZR 570 2013 Скачать руководство пользователя страница 219 | Manualshive

Страница: 219 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

5.13

PVT BREAK-IN (DRIVE BELT / CLUTCHES)

A proper break-in of the clutches and drive belt will
ensure a longer life and better performance. Break in the
clutches and drive belt by operating at slower speeds
during the 10 hour break-in period as recommended (see
Chapter 3 – Engine Break-In Period, page 3.37 for
break-in example). Pull only light loads. Avoid aggressive
acceleration and high speed operation during the break-
in period.

CLUTCH CENTER DISTANCE

INSPECTION

1.

Remove the outer PVT cover, drive belt, drive clutch
and driven clutch as outlined in this chapter.

NOTE

The inner PVT cover does not need to be removed to

check the clutch center to center distance.

2.

Install the Clutch Center Distance Tool (PU-50658)
onto the crankshaft and transmission input shaft. The
pictures below show the tool properly installed.

NOTE

The Clutch Center Distance Tool is used for the center-

to-center distance only. Make sure that the tool is

laterally aligned well with the machine and not binding

on the shafts.

3.

If the tool fits as shown above, the clutch center to
center distance is correct.

4.

If the tool does not fit as shown above, adjustment is
needed.

«
...
217
218
219
220
221
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: FARMA Страницы: 36

Бренд: Suzuki Страницы: 139

Бренд: Aeon Страницы: 196

Utility Vehicle Workshop

Бренд: Bush Hog Страницы: 11

Бренд: Vermeer Страницы: 88

Бренд: Landoll Страницы: 88

Бренд: KAYO MOTOR Страницы: 120

Бренд: Taylor-Dunn Страницы: 188

Бренд: KEEWAY Страницы: 110

Бренд: Yamaha Страницы: 431

SmarTrax John Deere 8X60 Series

Бренд: Raven Страницы: 48

Бренд: Winway Страницы: 67

FUGLEMAN SGW1000F-U2

Бренд: Segway Страницы: 184

FUGLEMAN SGW1000F-U2 2022

Бренд: Segway Страницы: 192

SNARLER ATV 2021 Series

Бренд: Segway Страницы: 386

Бренд: SSI SCHAEFER Страницы: 33

Eventa L Tandem

Бренд: IWT Страницы: 71

Бренд: FoldTrailer Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды