Polaris RZR 570 2013 Скачать руководство пользователя страница 218 | Manualshive

Страница: 218 / 482

background image

5.12

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

3.

Belts with thin spots, burn marks, etc., should be
replaced to eliminate noise, vibration, or erratic PVT
operation. See the Troubleshooting Chart at the end
of this chapter for possible causes.

BELT INSTALLATION

NOTE

Be sure to install belt in the same direction as it was

removed.

1.

Loop belt over the drive clutch and over the driven
sheave.

2.

BASE and INTL Models ONLY:

Loosen the driven

clutch retaining bolt to help spread the clutch
sheaves.

3.

LE Models ONLY:

Insert the belt removal tool (PN

2877408) into the driven clutch as shown.

NOTE

Make sure the tool is square with the moveable sheave

surface of the driven clutch.

4.

Rotate the tool towards the clutch to open the
sheaves.

5.

ALL Models:

Rotate the driven clutch and walk the

belt into the clutch.

6.

Rotate / spin the driven clutch and belt approximately
5-7 times to properly seat the belt in the driven
clutch.

7.

BASE and INTL Models ONLY:

Torque driven clutch

retaining bolt to specification.

TORQUE

Driven Clutch Retaining Bolt:

36 ft-lbs (49 Nm)

8.

Install the outer clutch cover and eight bolts. Torque
bolts to specification.

TORQUE

PVT Outer Clutch Cover bolts:

100 in-lbs (12 Nm)

«
...
216
217
218
219
220
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: Taylor-Dunn Страницы: 144

Бренд: Roketa Страницы: 15

Бренд: Duralite Страницы: 27

Бренд: Ultra-tow Страницы: 8

Бренд: swaploader Страницы: 94

Бренд: Toyhouse Страницы: 6

Бренд: U-Line Страницы: 9

Viper Jr. (RXL-40)

Бренд: E-TON Страницы: 23

Бренд: Kärcher Страницы: 346

Бренд: Range Road Страницы: 21

Roadster RT-622 2010

Бренд: Can-Am Страницы: 52

WARRIOR YFM350XNC

Бренд: Yamaha Страницы: 167

2009 Prowler XTZ

Бренд: Arctic Cat Страницы: 169

Бренд: Arctic Cat Страницы: 174

Бренд: Polaris Страницы: 231

Бренд: Herculano Страницы: 34

TrailPro Deluxe

Бренд: TransTank Страницы: 20

Бренд: Sno Jet Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды