Polaris RZR 570 2013 Скачать руководство пользователя страница 198 | Manualshive

Страница: 198 / 482

background image

4.38

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

POLARIS DIGITAL WRENCH

DIGITAL WRENCH® DIAGNOSTIC
SOFTWARE OVERVIEW

NOTE

Refer to Section 2, 3 and 4 in the Instruction Manual

provided in the Digital Wrench® Diagnostic Kit to install

the Polaris Digital Wrench® diagnostic software on your

computer.

The Digital Wrench® diagnostic software allows the
technician

to

perform

the

following

tests

and

observations:

• View or clear trouble codes
• Analyze real-time engine data
• Reflash ECU calibration files
• Perform guided diagnostic procedures
• Create customer service account records
• Perform output state control tests (some models)

SPECIAL TOOLS (DIGITAL WRENCH)

DIGITAL WRENCH® DIAGNOSTIC SOFTWARE

PART NUMBER

Digital Wrench® Diagnostic Kit

PU-47063-B

PU-47063-B (listed above) INCLUDES:

Digital Wrench® Software: PU-48731

Standard Interface Cable: PU-47151

SmartLink Module Kit: PU-47471

USB-Serial Adapter Cable: PU-50621

Fluke 73 Digital Multi-Meter or Fluke 77 DMM

PV-43546 (Fluke 77: PV-43568)

Laptop or Desktop Computer

Commercially Available (refer to diagnostic software
user manual or HELP section for minimum
requirements)

DIGITAL WRENCH SOFTWARE VERSION
AND UPDATE ID

Always use the most current version of the Digital
Wrench® software to ensure you have the latest updates
or enhancements. New reprogramming files and guided
diagnostic procedures are added to these updates as
they become available.

Knowing what Digital Wrench® version and update is
installed will help determine which updates are required.

NOTE

Versions and updates are subject to change.

1. Open the Digital Wrench® software. Locate the

version ID shown on the lower right side of the Digital
Wrench® start-up screen.

«
...
196
197
198
199
200
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: ADLY MOTO Страницы: 42

Бренд: E-Z-GO Страницы: 212

Бренд: Lenoxx Страницы: 16

Utility Vehicle Workshop

Бренд: Bush Hog Страницы: 11

Бренд: Vermeer Страницы: 88

Бренд: Sakai Страницы: 77

Бренд: CAMSO Страницы: 11

Adapt-X Optimax

Бренд: Apogee Страницы: 24

Бренд: Can-Am Страницы: 144

Stalwart Carry Fold 2

Бренд: M-WAVE Страницы: 6

Бренд: U.S. General Страницы: 23

Бренд: Yamaha Страницы: 859

Бренд: Chapman Страницы: 27

1988 Citation LS

Бренд: BOMBARDIER Страницы: 52

Бренд: BOMBARDIER Страницы: 80

Бренд: Opus Страницы: 21

GO-4 EV INTERCEPTOR IV

Бренд: Westward Страницы: 56

TRACKER LX6 EFI

Бренд: Textron Specialized Vehicles Страницы: 168

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды