Polaris RZR 570 2013 Скачать руководство пользователя страница 187 | Manualshive

Страница: 187 / 482

Polaris RZR 570 2013 Скачать руководство пользователя страница 187

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

4.27

TEMPERATURE AND MANIFOLD ABSOLUTE PRESSURE SENSOR (T-MAP)

OPERATION OVERVIEW

Mounted on the throttle body intake manifold, the T-MAP
sensor performs two functions in one unit.

Air passing through the intake is measured by the T-MAP
and relayed to the ECU. These signals, comprised of
separate air temperature and manifold absolute pressure
readings, are processed by the ECU and compared to its
programming for determining the fuel and ignition
requirements during operation. The T-MAP sensor
provides the ECU with engine load data.

T-MAP SENSOR TEST

The T-MAP sensor is a non-serviceable item. If it is
faulty, it must be replaced.

NOTE

This sensor should only be tested using the Digital

Wrench® Diagnostic Software (dealer only).

T-MAP SENSOR REPLACEMENT

1.

Remove the drivers seat and disconnect the
negative (-) battery cable.

2.

Remove the cargo box access panel.

3.

Disconnect vehicle harness from T-MAP sensor.

4.

Remove the retaining bolt and remove the sensor
from the intake boot.

5.

Use a light coating of soapy water on the grommet to
aid installation of the new sensor.

6.

Install the sensor by inserting it with a twisting motion
to properly seat the grommet.

7.

Install the retaining bolt and torque to specification.

TORQUE

T-MAP Retaining Bolt:

24 in-lbs (2.8 Nm)

«
...
185
186
187
188
189
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды