Polaris RZR 570 2013 Скачать руководство пользователя страница 181 | Manualshive

Страница: 181 / 482

background image

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

4.21

FUEL PUMP REPLACEMENT

WARNING

Always wear safety goggles when working with high

pressure or flammable fluids. Failure to do so could

result in serious injury or complications.

1.

Remove the driver and passenger seat to access the
fuel pump.

2.

Disconnect the battery (-) negative cable.

3.

Ensure that static has been discharged from you by
touching a ground source such as the engine or
frame.

4.

Disconnect the fuel pump electrical harness.

5.

While holding a shop towel over the fuel line
connector, disconnect the quick connect fuel line
from the fuel pump.

CAUTION

It is possible for pressurized fuel to be present when

disconnecting the fuel line.

It is recommended to allow the vehicle to sit for a

period of one hour after shutting off the engine before

servicing the fuel pump. This allows the exhaust to cool

and fuel pressure to drop.

NOTE

A small amount of fuel may come out of the fuel line or

tank. Properly drain fuel into a suitable container.

6.

Be sure the top of the fuel tank is clean. If it requires
cleaning, hand wash the top of the tank to ensure no
debris will enter the fuel system when the fuel pump
is removed.

WARNING

Failure to clean area around fuel pump may lead to

debris entering the fuel tank during service. Excessive

debris in fuel tank may cause premature wear of fuel

pump and/or cloggingof internal fuel filters.

7.

Place the Fuel Pump Service Tool (PU-50326) over
the fuel pump PFA nut. Using a 1/2” drive ratchet or
breaker bar, loosen and remove the PFA nut.
Discard the PFA nut.

NOTE

Apply downward force on the fuel pump flange while

removing the fuel pump PFA nut.

«
...
179
180
181
182
183
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZR 570 2013

Бренд: J&M Страницы: 26

Бренд: KAYO MOTO Страницы: 9

Бренд: FEISHEN Страницы: 41

LEXION 770 2016

Бренд: Claas Страницы: 48

Бренд: Taylor-Dunn Страницы: 136

Бренд: Yamaha Страницы: 222

YXZ 1000 R SS 2023

Бренд: Yamaha Страницы: 216

Бренд: Suzuki Страницы: 33

Бренд: HYOSUNG Страницы: 48

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 141

Бренд: Yamaha Страницы: 262

GE-YX125 series

Бренд: GMX Страницы: 18

Бренд: Landoll Страницы: 80

MKII 600 Series

Бренд: NC ENGINEERING Страницы: 80

Бренд: Agri-Fab Страницы: 12

Grizzly 450 YFM45FGPD

Бренд: Yamaha Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды