Polaris RZR 570 2013 Скачать руководство пользователя страница 179 | Manualshive

Страница: 179 / 482

Polaris RZR 570 2013 Скачать руководство пользователя страница 179

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

4.19

FUEL SENDER TEST

If the fuel gauge reading on the instrument cluster is not
working, or if the display reading differs in large
comparison to the fuel in the tank, perform a resistance
test on the fuel sender.

Disconnect the fuel pump / sending unit connection and
measure the resistance. If out of specification, replace
the fuel pump assembly.

Fuel Sender Resistance Specifications:

Full: 6 ± 1 Ω

Empty: 90 ± 4.5 Ω

FUEL PUMP TEST

If a fuel delivery problem is suspected, make certain the
fuel pump filters are not plugged, that the pump is being
activated through the ECU, all electrical connections are
properly secured, the fuses are good, and a minimum of
7.0 volts is being supplied. If during starting the battery
voltage drops below 7.0 volts, the ECU will fail to operate
the system.

WARNING

Fuel is extremely flammable and may cause severe

burns, injury, or death.

Do not use any device that produces a flame or

electrical devices that may spark around fuel or fuel

vapors.

1.

Remove the passenger seat from the vehicle.

2.

Cover the fuel line connection at the fuel tank with a
shop towel and disconnect the line from the fuel
pump outlet.

3.

Install the Fuel Pressure Gauge Adaptor (PV-48656)
in-line between the fuel pump outlet and fuel line.

4.

Connect the hose from the Fuel Pressure Gauge Kit
(PU-43506-A) to the test valve on the Fuel Pressure
Gauge Adaptor (PV-48656). Route the clear hose
into a portable gasoline container or the vehicle’s
fuel tank.

«
...
177
178
179
180
181
...
»

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды