Polaris RZR 570 2013 Скачать руководство пользователя страница 152

Страница: 152 / 482

3.80

9926813 R04 - 2013-2016

RZR

570 Service Manual

ENGINE ASSEMBLY - BOTTOM END

CRANKCASE ASSEMBLY – PTO SIDE

Lubricate all crankcase bearings with engine oil.
Clean sealing surface to remove all oil sealant.

NOTE

Apply Loctite® 641 to the inner race of each of the

crank bearings.

Place crankcase on a sturdy work bench.

Carefully set the PTO crankcase onto the PTO side
of the crankshaft.

Align the connecting rod with the cylinder area of the
crankcase.

Install the crankshaft removal / installation tool on to
the PTO side crankcase.

Crankshaft Removal / Installation Tool

PU-50784

• Install plate

over adapter

• Evenly attach the assembly onto the PTO side

crankcase using the four bolts as shown.

• Place the nut and large washer onto the crankshaft

installation screw.

• Insert the crankshaft installation screw through the

threaded portion of the adaptor

• Fully thread the crankshaft installation screw into the

clutch bolt threads of the crankshaft.

• With the help of an assistant holding the crankshaft,

firmly hold the crankshaft installation screw with a
wrench while tightening the large nut against the
adaptor

With the help of an assistant, slowly tighten the nut
until the crankshaft is completely seated into the
crankcase bearings.

Remove the crankshaft removal / installation tool
from the crankcase.

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды