Polaris RZR 570 2013 Скачать руководство пользователя страница 151

Страница: 151 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

3.79

OIL PICKUP ASSEMBLY INSPECTION

The oil pickup assembly is located in the Mag side
crankcase

Pull and twist to remove the oil pickup assembly from
the crankcase.

Inspect the assembly for cracks and excessive wear.
Replace if necessary.

Remove and discard the O-ring.

Thoroughly clean the pickup assembly

Replace the o-ring and lubricate with clean engine
oil.

Press the pickup assembly into the crankcase until
fully seated.

OIL PRESSURE REGULATOR (BYPASS)
VALVE INSPECTION

The oil pressure regulator (bypass) valve is located in the
Mag side crankcase

Use a brass drift to press out the oil pressure valve
from the crankcase.

Replace the oil pressure valve if the inner plunger
binds, sticks or does not operate smoothly.

Remove and discard the o-ring.

Thoroughly clean the valve.

Replace the o-ring and lubricate with clean engine
oil.

Press the oil pressure valve into the crankcase until
fully seated.

CRANKCASE INSPECTION

Remove all traces of gasket sealer from the
crankcase mating surfaces. Inspect the surfaces
closely for nicks, burrs or damage.

Be sure alignment pins are in place where used.

Be sure oil passages are clean and free of any
cleaning solvent.

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды