Polaris RZR 570 2013 Скачать руководство пользователя страница 121

Страница: 121 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

3.49

Record measurements taken in Step 4. If cylinder is
tapered, or out of round beyond .001, cylinder must
be re-bored oversize, or replaced.

Cylinder Taper Limit:

.001″ Max. (0.025 mm)

Cylinder Out of Round Limit:

.001″ Max. (.025 mm)

Standard Bore Size:

3.8976 +/- 0.0003″ (99.0 +/- 0.008 mm)

PISTON REMOVAL

Note piston directional indicator “EX” positioned
toward the exhaust side of engine.

Remove piston circlip and push piston pin out of
piston. If necessary, heat the crown of the piston

slightly

with a heat gun.

CAUTION

Do not apply heat to the piston rings, they may lose

radial tension.

Remove top ring.

*Using a piston ring pliers

: Carefully expand ring

and lift it off the piston.

CAUTION

Do not expand the ring more than the amount

necessary to remove it from the piston.

*By hand:

Using both thumbs, spread the ring open

and push up on the opposite side.

Repeat procedure for second ring.

Remove oil control ring top rail first, then bottom rail.

Remove oil control ring expander.

PISTON-TO-CYLINDER CLEARANCE

Measure the outside diameter of the piston 12 mm
from the skirt and at a right angle to the direction of
the piston pin

Subtract this measurement from the maximum
cylinder size measurement from cylinder inspection.

Piston to Cylinder Clearance:

.00019 - .00216″ (.005 - .055 mm)

Piston O.D.:

3.8957 - 3.8968″ (98.953 - 98.980 mm)

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды