Polaris RZR 570 2013 Скачать руководство пользователя страница 105

Страница: 105 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

3.33

29. Remove the four bolts and nuts (M) securing the

engine to the front motor mount bracket.

30. Remove the eight bolts (N) securing the coupler

brackets to the engine and transmission.

31. Loosen the two bolts and nuts (O) so the engine

mount bracket can be slightly tilted away from
engine.

32. With the help of an assistant and the engine hoist,

raise the engine vertically out of the vehicle frame.

NOTE

Have an assistant help guide the engine in and out of

the vehicle while using an engine hoist to prevent

personal injury or damage to the vehicle components.

33. Install the engine stand adapter onto the engine PTO

side mounting ears as shown below.

Engine Stand Adapter

PU-50824

34. Select the proper engine stand sleeve adapter and

install it onto the engine stand adapter.

Sleeve adapter for a 2″ bore engine stand:

PU-50625

Sleeve adapter for a 2.375″ bore engine stand:

PW-47054

35. Place engine onto the engine stand for service.

Engine Stand

PU- 50624

ENGINE INSTALLATION

Use the following procedure to reinstall the engine
assembly.

Attach engine with suitable lifting straps to an
overhead or portable engine hoist.

Remove the engine stand adapter plate.

Use the overhead or portable engine hoist and
suitable engine straps to lower the engine into the
vehicle frame.

NOTE

Have an assistant help guide the engine in and out of

the vehicle while using an engine hoist to prevent

personal injury or damage to vehicle components.

By hand, install the four front engine mount bolts and
nuts (A). Do not tighten at this time.

Instal the four engine to transmission coupler plates
(B) and instal the eight bolts and washers (C). Do not
tighten fasteners at this time.

NOTE

DO NOT torque fasteners at this time.

ENGINE / COOLING SYSTEM

Содержание RZR 570 2013



































































































































































































































































































































































































































































































Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды

Polaris RZR 570 2013, Руководство по обслуживанию

Результаты поиска

Содержание RZR 570 2013

Отзывы:

Похожие инструкции для RZR 570 2013

Бренды по названию

Популярные бренды