Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 447

background image

2.28

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

© Copyright Polaris Sales Inc.

WARNING

Never remove the pressure cap when the engine is

warm or hot. Escaping steam can cause severe burns.

The engine must be cool before removing the pressure

cap.

5.

Remove the pressure cap. Using a funnel, add
coolant to the top of the radiator filler neck.

6.

Reinstall the pressure cap.

NOTE

Use of a non-standard pressure cap will not allow the

recovery system to function properly.

7.

Remove the recovery bottle cap and add coolant
using a funnel.

8.

Fill the recovery bottle to the “MAX” mark with the
recommended pre-mix coolant. You may use a 50/50
or 60/40 mixture of antifreeze and distilled water as
required for freeze protection in your area.

FLUID CAPACITY

Recommended Anti-Freeze/Coolant:

Polaris Premium

Pre-Mixed Antifreeze

(PN 2871534) (Quart)(PN 2871323) (Gallon)

9.

Reinstall the recovery bottle cap.

10. If coolant was required, start engine and check for

leaks. Make sure radiator fins are clean to prevent
overheating.

COOLING SYSTEM HOSES

1.

Inspect all vehicle hoses for cracks, deterioration,
abrasion or leaks. Replace if necessary.

2.

Inspect all engine hoses for cracks, deterioration,
abrasion or leaks. Replace if necessary.

3.

Check tightness and condition of all hose clamps.

CAUTION

Do not over-tighten hose clamps at radiator, or radiator

fitting may distort.Radiator hose clamp torque is

36 in-

lbs (4 Nm)

.

«
...
43
44
45
46
47
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Pioneer SXS500M 2018

Бренд: Honda Страницы: 268

Бренд: Aeon Страницы: 126

DRIFTER 10-0550

Бренд: Kolpin Страницы: 17

can-am MAVERICK SPORT MAX 2003 Series

Бренд: BRP Страницы: 212

Transporta CCT 5221

Бренд: Ifor Williams Trailers Страницы: 45

Бренд: BOMBARDIER Страницы: 129

TRX90 Sportrax 90

Бренд: Honda Страницы: 208

Бренд: Polaris Страницы: 109

Бренд: Jacobsen Страницы: 76

Бренд: Kayoba Страницы: 16

WOLVERINE YXE70WPXH

Бренд: Yamaha Страницы: 186

Бренд: Taylor-Dunn Страницы: 188

Бренд: Taylor-Dunn Страницы: 206

Бренд: Taylor-Dunn Страницы: 260

Бренд: Yamaha Страницы: 56

Бренд: Yamaha Страницы: 478

Бренд: Equinox Systems Страницы: 6

Бренд: ShoreLand'r Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды