Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 392

Страница: 392 / 447

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

10.7

VEHICLE SPEED SENSOR

SPEED SENSOR LOCATION

The speed sensor (A) is located on the ride side of the
transmission, accessed through the right rear wheel well.

SPEED SENSOR TESTING

Special Tools Required:
Static Timing Light Harness (PN 2871745)
Hall Sensor Probe Harness (PN 2460761)

Disconnect the 3 wire harness from the speed
sensor

and

remove

the

sensor

from

the

transmission.

Connect the wires from the Static Timing Light
Harness to the sensor 3 pin connector using the Hall
Sensor Probe Harness (PN 2460761).

Pass a screwdriver back and forth in front of the
sensor tip.

Be sure connections are good and 9V battery is in
good condition. If the light flashes, the sensor is
good.

ELECTRICAL

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды

Polaris RANGER CREW 900 2014, Руководство пользователя

Результаты поиска

Содержание RANGER CREW 900 2014

Отзывы:

Похожие инструкции для RANGER CREW 900 2014

Бренды по названию

Популярные бренды