Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 295 | Manualshive

Страница: 295 / 447

background image

7.8

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

© Copyright Polaris Sales Inc.

FRONT PROPSHAFT

REMOVAL / INSTALLATION

1.

Remove the front bumper (see Chapter 5).

2.

Elevate and safely support vehicle under the frame.
The use of a vehicle hoist is recommended for this
procedure.

CAUTION

Serious injury may result if machine tips or falls. Be

sure machine is secure before beginning this service

procedure. Wear eye protection when removing

bearings and seals.

3.

Remove the front gearcase from the vehicle (see
"Front Gearcase Removal" provided in this chapter).

4.

Pull the front propshaft towards the front of the
vehicle until the splines on the rear yoke disengage
from the transmission snorkel shaft. Remove the
propshaft out the front of the vehicle as shown.

NOTE

If the propshaft does not fully disengage from the

transmission snorkel shaft, remove the skid plate to

access the front engine mount support. Remove the (2)

driver's side engine mount nuts. Doing so will allow you

to lift up on the engine to get more clearance between

the propshaft and the steel skid plate.

5.

Reverse

this

procedure

to

reinstall

the

front

propshaft. Use a NEW roll pin upon installation.

REMOVAL / INSTALLATION - CREW

Removal

1. Remove the front bumper (see Chapter 5).

2. Elevate and safely support vehicle under frame. The

use of a vehicle lift is recommended for this
procedure.

3. Remove the front gearcase (see “Front Gearcase

Removal”).

4. Separate the front section of the propshaft assembly

from the splines in front of the flex bearing A (Fig. 1).

5. Remove the front skid plate.

6. Remove the rear skid plate.

7. Remove rear floor (see Rear Floor - CREW in

Chapter 5).

8. Remove the (2) fasteners (B) Fig. 2 securing the flex

bearing to the frame.

9. Slide the rear section of the propshaft assembly from

the transmission output shaft.

10. Remove the propshaft assembly through the rear

floor opening.

«
...
293
294
295
296
297
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Бренд: E-Z-GO Страницы: 158

WOLVERINE YFM45FXV

Бренд: Yamaha Страницы: 34

BLASTER YFS200S

Бренд: Yamaha Страницы: 46

Бренд: Eton America Страницы: 96

FourTrax Rancher TRX420FE1 2020

Бренд: Honda Страницы: 273

Бренд: SAF-HOLLAND Страницы: 20

Бренд: Yamaha Страницы: 17

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 156

BLASTER YFS200P

Бренд: Yamaha Страницы: 156

BLASTER YFS200N

Бренд: Yamaha Страницы: 153

Бренд: Yamaha Страницы: 153

Бренд: Yamaha Страницы: 155

BIG BEAR YFM400S

Бренд: Yamaha Страницы: 171

Бренд: Yamaha Страницы: 191

Бренд: X-TREME Страницы: 26

Бренд: Polaris Страницы: 14

Бренд: PARKIT360 Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды