Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 263 | Manualshive

Страница: 263 / 447

background image

6.14

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual

© Copyright Polaris Sales Inc.

BELT INSPECTION

1.

Inspect belt for hour glassing (extreme circular wear
in at least one spot and on both sides of the belt).
Hour glassing occurs when the drive train does not
move and the drive clutch engages the belt.

2.

Inspect belt for loose cords, missing cogs, cracks,
abrasions, thin spots, or excessive wear. Compare
belt measurements with a new drive belt. Replace if
necessary.

3.

Belts with thin spots, burn marks, etc., should be
replaced to eliminate noise, vibration, or erratic PVT
operation. See the Troubleshooting Chart at the end
of this chapter for possible causes.

BELT INSTALLATION

NOTE

Be sure to install belt in the same direction as it was

removed.

1.

Install belt over drive clutch and start to install belt
over driven clutch. While pushing down on the belt,
turn the driven clutch clockwise. Work the belt down
in the clutch to give more slack. Note: On 2014 Non-
EBS Models the driven clutch mounting bolt should
be loose to allow the clutch sheaves to spread.
Torque driven clutch mounting bolt to specification.

TORQUE

Driven Clutch Retaining Bolt:38 ft-lbs (52 Nm)

2.

Install the outer clutch cover and (8) screws. Torque
screws to specification.

TORQUE

Outer Clutch Cover Retaining Screws:54 in-lbs (6.1

Nm)

3.

Install the grease zerk fitting on the upper rear
control arm and torque to specification.

TORQUE

Grease Zerk Fitting:54 in-lbs (6.1 Nm)

4.

Install the airbox to the frame and torque the
mounting bolts to specification.

TORQUE

Airbox Mounting Screws:8 ft-lbs (11 Nm)

5.

Install both intake hoses to the airbox. Tighten the
hose clamps to specification.

TORQUE

Intake Hose Clamps:35 in-lbs (4 Nm)

PVT BREAK-IN (DRIVE BELT / CLUTCHES)

A proper break-in of the clutches and drive belt will
ensure a longer life and better performance. Break in the
clutches and drive belt by operating at slower speeds
during the 10 hour break-in period as recommended (see
Chapter

3

“Engine

Break-In

Period”

for

break-in

example). Pull only light loads. Avoid aggressive
acceleration and high speed operation during the break-
in period.

«
...
261
262
263
264
265
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Бренд: Lynx Страницы: 113

DIRT QUAD 25117460

Бренд: Razor Страницы: 12

Бренд: Toro Страницы: 28

Бренд: Suzuki Страницы: 528

Formula Mx 1988

Бренд: BOMBARDIER Страницы: 62

traxter max series

Бренд: BOMBARDIER Страницы: 174

outlander max 800

Бренд: BOMBARDIER Страницы: 160

Бренд: BOMBARDIER Страницы: 282

Sportsman 9921169

Бренд: Polaris Страницы: 137

250GKA-2Z Series

Бренд: Kandi USA Страницы: 16

Бренд: Jayco Страницы: 93

Бренд: Landa Страницы: 30

Бренд: VARES Страницы: 44

Бренд: Taylor-Dunn Страницы: 162

Бренд: Kellfri Страницы: 32

Бренд: Yamaha Страницы: 193

Бренд: Wallenstein Страницы: 45

1990 DS Gasoline Golf Car

Бренд: Club Car Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды