Polaris RANGER CREW 900 2014 Скачать руководство пользователя страница 176 | Manualshive

Страница: 176 / 447

background image

9924880 Rev 2- 1/10/2014 - 2013 / 2014 RANGER XP 900 - 2014 RANGER XP 900 / CREW 900 Service Manual
© Copyright Polaris Sales Inc.

4.27

ENGINE COOLANT TEMPERATURE SENSOR (ECT)

OPERATION OVERVIEW

Mounted in the cylinder head, the engine temperature
sensor measures coolant temperature. The engine
temperature

sensor

is

a

Negative

Temperature

Coefficient (NTC) type sensor, as the temperature
increases the resistance decreases.

Coolant passes through the cylinder head and by the
sensor probe, varying a resistance reading which is
relayed to the ECU. This signal is processed by the ECU
and compared to its programming for determining the
fuel and ignition requirements during operation. The ECU
also uses this signal to determine when to activate the
cooling fan during operation.

ECT SENSOR TEST

To quickly rule out other components and wiring related
to the ECT, disconnect the harness from the ECT sensor
and start the engine. After a few seconds, the fan should
turn on and the “Check Engine” indicator should display
on the instrument cluster. This indicates all other
components are working properly.

Refer

to

Chapter

10

for

additional

ECT sensor

information. Polaris dealers can test the sensor by using
Digital Wrench® Diagnostic Software (dealer only).

ECT Sensor Resistance Readings

TEMPERATURE °F (°C)

RESISTANCE

68 °F (20 °C)

2.5k Ω ± 6%

86 °F (30 °C)

1.7k Ω ± 6%

TEMPERATURE °F (°C)

RESISTANCE

104 °F (40 °C)

1.2k Ω ± 6%

122 °F (50 °C)

834 Ω ± 6%

140 °F (60 °C)

596 Ω ± 6%

158 °F (70 °C)

435 Ω ± 6%

176 °F (80 °C)

323 Ω ± 6%

194 °F (90 °C)

243 Ω ± 6%

212 °F (100 °C)

186 Ω ± 6%

ECT SENSOR REPLACEMENT

1.

Lift the rear cargo box to the raised position.

2.

Drain the coolant so the level is below the sensor
(see Chapter 2 “Coolant Drain / Fill”).

3.

Remove the fuel line from fuel rail (see “Fuel Line
Removal / Installation”).

4.

Disconnect the vehicle harness from the ECT sensor.

5.

Using a wrench, loosen and remove ECT sensor
from engine.

6.

Apply thread sealant to the new sensor threads and
install it into the cylinder head.

7.

Torque the new ECT sensor to specification and
connect the vehicle harness to the sensor.

TORQUE

ECT Sensor:

17 ft-lbs (23 Nm)

8.

Reconnect the fuel line to the fuel rail.

9.

Add the required amount of coolant and bleed the
system (see Chapter 3 “Cooling System Bleeding
Procedure”).

FUEL SYSTEM - GENERAL

«
...
174
175
176
177
178
...
»

Содержание RANGER CREW 900 2014
































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RANGER CREW 900 2014

Бренд: Polaris Страницы: 147

Бренд: cascade corporation Страницы: 16

Бренд: Toro Страницы: 32

Бренд: Suzuki Страницы: 624

Renegade 1000R 2016

Бренд: Can-Am Страницы: 534

Бренд: LONCIN Страницы: 156

Бренд: MasterCraft Страницы: 33

Бренд: Dometic Страницы: 96

Бренд: Jayco Страницы: 124

Бренд: Baja Страницы: 82

MINI BAJA DUNE65

Бренд: Baja motorsports Страницы: 8

Бренд: Yamaha Страницы: 405

Бренд: Landa Страницы: 38

Бренд: Landa Страницы: 101

Бренд: PRONAR Страницы: 133

Бренд: PRONAR Страницы: 136

Expediter EX-21 2017

Бренд: Columbia Страницы: 32

Бренд: Yamaha Страницы: 374

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды