Polaris ATV 2002 Скачать руководство пользователя страница 86

Страница: 86 / 181

RIDING

Safe Riding Tips

Turning Around On A Hill

8’

Uphill

If the ATV stalls while climbing a hill, never back it down the

hill! One maneuver which can be used when it is necessary

to turn around while climbing a hill is the K-turn.

1. Stop and lock the parking brake while maintaining body weight

uphill.

2. Leave transmission in forward and shut off engine.

3. Dismount on left or uphill side of ATV.
4. Staying uphill of ATV, turn handlebars full left (while facing front

of ATV).

5. While holding service brake, release parking brake lock and slowly

allow ATV to roll around to your right until ATV is pointing across

the hill or slightly downward.

6. Lock the parking brake and remount ATV from the uphill side,

maintaining body weight uphill.

7. Restart engine with transmission still in forward, release parking

brake, and proceed slowly, controlling speed with the service

brake, until ATV is on reasonably level ground.

Avoid climbing steep hills. Loss of vehicle control or overturning of

the ATV could occur resulting in severe injury or death.

WARNING

Содержание ATV 2002






















































































































































































Результаты поиска

Содержание ATV 2002

Отзывы:

Polaris ATV 2002, Руководство пользователя, Страница: 86 / 181

Результаты поиска

Содержание ATV 2002

Отзывы: