Polaris ATV 2002 страница 70 Скачать руководство пользователя

Страница: 70 / 181

OPERATION

Break-In Period

2-Cycle Engines

The break in period for your new Polaris ATV is defined as the time it

takes to use the first tank of gasoline. No single action on your part is

as important as a proper break in period. Careful treatment of a new

engine will result in more efficient performance and longer life for the

engine. Perform the following procedures carefully.

1. Mix 12.8 ounces of injection oil to four gallons (or 16 ounces to 5

gallons) of gasoline in a suitable gas can. Fill the fuel tank as

outlined on page 49.

2. Fill the oil tank with Polaris injection oil.

3. Drive slowly at first. Select an area which is open and will give

you room to familiarize yourself with vehicle operation and

handling.

4. Vary the throttle positions.
5. Perform regular checks on fluid levels, controls and all important

areas on the vehicle as outlined earlier on the daily pre-ride

inspection checklist found on page 66.

Use only Polaris injection oil. Never substitute or mix oil brands.

Serious engine damage and voiding of warranty can result.

CAUTION

Do not operate at full throttle or high speeds for extended

periods during the first three hours of use. Excessive heat can

build up and cause damage to close fitted engine parts.

CAUTION

Содержание ATV 2002






















































































































































































Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды

Polaris ATV 2002, Руководство пользователя

Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды