Polaris ATV 2002 Скачать руководство пользователя страница 51

Страница: 51 / 181

CONTROLS AND FEATURES

Controls

Auxiliary Brake

Your Polaris ATV has an auxiliary brake (1) provided as a safety

feature. It is located on the inside of the right floor board and is

operated by the right foot. It is intended as a backup to the main brake

system, especially if the main system becomes inoperative.
If the rear wheels slide, reduce brake pedal pressure to brake the rear

wheels without skidding. Aggressively applying the rear brake when

backing down a hill may cause rear tip over.

Brake Fluid Level

It will be necessary to check the brake fluid level for the auxiliary

brake system. The reservoir is located under the seat or near the foot

brake. The fluid should be kept between the maximum and minimum

marks.

Use caution when applying the auxiliary brake. Do not

aggressively apply the auxiliary brake when going forward or the

rear wheels may skid and slide sideways causing loss of control.

WARNING

Содержание ATV 2002






















































































































































































Результаты поиска

Содержание ATV 2002

Отзывы:

Polaris ATV 2002, Руководство пользователя, Страница: 51 / 181

Результаты поиска

Содержание ATV 2002

Отзывы: