background image

175

WARRANTY

ALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED

TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN

DURATION TO THE ABOVE SIX MONTH WARRANTY PERIOD.

POLARIS FURTHER DISCLAIMS ALL EXPRESS WARRANTIES

NOT STATED IN THIS WARRANTY. Some states do not allow

limitations on how long an implied warranty lasts, so the above

limitation may not apply to you if inconsistent with controlling state

law.

HOW TO OBTAIN WARRANTY SERVICE

If your ATV requires warranty service, you must take it to a Polaris

dealer authorized to repair Polaris ATVs. When requesting warranty

service you must present your copy of the Warranty Registration form

to the dealer. (THE COST OF TRANSPORTATION TO AND FROM

THE DEALER IS YOUR RESPONSIBILITY). Polaris suggests that

you use your original selling dealer; however, you may use any Polaris

Servicing Dealer to perform warranty service.
Please work with your dealer to resolve any warranty issues. Should

your dealer require any additional assistance they will contact the

appropriate person at Polaris.
This warranty gives you specific legal rights, and you may also have

other rights which vary from state to state.
If any of the above terms are void because of state or federal law, all

other warranty terms will remain in effect.
Engine Oil
1. Always use Polaris engine oil.
2. Never substitute or mix oil brands as serious engine damage and

voiding of warranty can result.

Содержание ATV 2002






















































































































































































Отзывы: