Polaris ATV 2002 Скачать руководство пользователя страница 171

Страница: 171 / 181

168

MAINTENANCE AND LUBRICATION

Cleaning and Storage

If you choose not to use Polaris fogging Oil, perform the following

procedure.
1. Support the front end of the machine so the engine is level or tilted

slightly rearward.

2. Remove spark plug(s). Rotate piston to BDC and pour

approximately two ounces of Polaris 2 Cycle Injector oil into the

cylinder.

3. Turn the engine over several times to ensure coverage of piston

rings, cylinder walls and crankshaft bearings.

4. Treat the fuel system with Polaris Carbon Clean.
5. If Polaris fuel system additive is not used, fuel tank, fuel lines, and

carburetor should be completely drained of gasoline. to eliminate

any fuel remaining in the carburetor, run the engine until it stops.

Transporting

Whenever the ATV is to be transported the following measures should

be taken.
1. Turn off the engine and remove the key. It may be lost if not

removed.

2. Turn the fuel valve to off.
3. Be certain the fuel cap, oil cap, and seat are installed correctly.
4. Always tie the frame of the ATV to the transporting unit securely

using suitable straps or rope.

5. Always place the transmission in gear and lock the parking brake.

Содержание ATV 2002






















































































































































































Результаты поиска

Содержание ATV 2002

Отзывы:

Polaris ATV 2002, Руководство пользователя, Страница: 171 / 181

Результаты поиска

Содержание ATV 2002

Отзывы: