Polaris ATV 2002 страница 168 Скачать руководство пользователя

Страница: 168 / 181

165

MAINTENANCE AND LUBRICATION

Cleaning and Storage

Cleaning Your ATV

Keeping your ATV clean will not only improve its appearance but it

can also extend the life of various components. With a few

precautions, your ATV can be cleaned much like an automobile.

Washing

If a high pressure type car wash system is used, extreme care must be

taken to avoid water damage to the wheel bearings, transmission seals,

body panels, brakes and warning labels. Many expensive repair bills

can result from using high pressure detergent systems.

NOTE:

If a high pressure car wash is used, grease all zerk fittings

immediately after washing. Also run the vehicle to evaporate any

water that might have entered the engine or exhaust system.
The best and safest way to clean your ATV is with a garden hose and a

pail of mild soap and water. Use a professional type washing mitten,

cleaning the upper body first and the lower parts last. Rinse with water

frequently and dry with a chamois to prevent water spots.

NOTE:

warning labels are damaged, contact your a Polaris dealer for free

replacement.

Waxing

Your ATV can be waxed with any non-abrasive automotive paste wax.

Avoid the use of harsh cleaners since they can scratch the body finish.

Certain products, including insect repellants and chemicals, will

damage plastic surfaces. Care must be taken when using these

products near plastic surfaces.

CAUTION

Содержание ATV 2002






















































































































































































Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды

Polaris ATV 2002, Руководство пользователя

Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды