Polaris ATV 2002 страница 153 Скачать руководство пользователя

Страница: 153 / 181

150

MAINTENANCE AND LUBRICATION

Lights -- Adjustment -- Replacement

High Beam Headlight Adjustment (Gen IV)

The headlight beam can be adjusted to any position desired by turning

the adjusting knob located on the bottom right side of the headlight

pod.
1. Place the vehicle on a level surface with the headlight

approximately 25’ (7.6 m) from a wall.

2. Measure the distance from the floor to the center of the headlight

and make a mark on the wall at the same height.

3. Start the engine and turn the headlight switch to high beam.
4. Observe headlight aim. The most intense part of the headlight

beam should be aimed 2

″

(5.1 cm) below the mark placed on the

wall in step 1.

NOTE:

Rider weight must be included on the

seat.

5. Adjust beam to desired position by turning the adjustment knob.

Содержание ATV 2002






















































































































































































Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды

Polaris ATV 2002, Руководство пользователя

Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды