Polaris ATV 2002 страница 139 Скачать руководство пользователя

Страница: 139 / 181

136

MAINTENANCE AND LUBRICATION

Adjustments

Carburetor/Engine Idle RPM Adjustment

2 Cycle Engines

If the engine idle speed is not satisfactory, and all other conditions are

favorable, the carburetor can be adjusted as follows:
1. Warm up the engine by

running the vehicle

approximately five minutes.

2. Place the transmission in gear

with the parking brake

applied.

3. Adjust the carburetor idle

screw in or out until the

desired idle RPM is reached.

Turning the screw in

(clockwise) will raise RPM.

Turning the screw out

(counterclockwise) will lower

RPM.

The following variations to air screw adjustment for 2-Cycle engines

should be noted:

For improving cold weather start and reducing audible detonation

noise, the air screw can be closed from 1/2 to 1 turn by turning the

screw clockwise.

During hot weather and/or high altitude operation the air screw can

be adjusted for smooth operation by approximately 2 turns counter-

clockwise.

Idle

Screw

Air Screw

Содержание ATV 2002






















































































































































































Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды

Polaris ATV 2002, Руководство пользователя

Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды