Polaris ATV 2002 Скачать руководство пользователя страница 136

Страница: 136 / 181

133

MAINTENANCE AND LUBRICATION

Adjustments

Handlebar Adjustment

Your ATV has handlebars which

can be adjusted for your

personal fit.
1. Locate handlebar bolts. On

models with a headlight

pod, it will be necessary to

remove the upper headlight

pod. On other models

remove the handlebar cover.

2. Loosen the four bolts.
3. Adjust handlebar to desired

height. Be sure handlebars

do not hit gas tank or any

other part of machine when

turned fully to left or right.

4. Torque handlebar adjuster

block bolts to 10 to 12 ft.

lbs.

NOTE:

Tighten bolts so there

is an equal gap at the front and

rear of the handlebar block.

Improper gap will result in

improper fit of upper pod.

Improper adjustment of the handlebars or incorrect torquing of

the adjuster block tightening bolts can cause limited steering or

loosening of the handlebars, resulting in loss of control and

possible serious personal injury or death.

WARNING

Содержание ATV 2002






















































































































































































Результаты поиска

Содержание ATV 2002

Отзывы:

Polaris ATV 2002, Руководство пользователя, Страница: 136 / 181

Результаты поиска

Содержание ATV 2002

Отзывы: