Polaris ATV 2002 страница 125 Скачать руководство пользователя

Страница: 125 / 181

122

MAINTENANCE AND LUBRICATION

Lubrication

Front Gearcase Lubrication

The front gearcase fill plug is

located as shown.
The front gearcase lubricant level

should be checked every six months

or 1000 miles (1600 km), whichever

comes first. Front gearcase oil

should be changed annually.

Type A

- With the ATV on a level

surface, remove fill plug and check

the lubricant level. Lubricant

should be kept at the bottom of fill

plug thread. The correct gearcase

lubricant to use is GL5 80-90

Weight Gear Lube.

Type B

- The lubricant level in this

type of gearcase cannot be checked.

You must periodically drain it and

refill it according to the following

procedure.

Gearcase Oil Changing

Procedure

1. Remove fill plug (1).

2. Remove gearcase drain plug

located on the bottom right

hand side and drain the oil.

3. Clean and reinstall the drain

plug and tighten securely (14 ft.

lbs/1.93 kgm).

4. Add 4 ounces (120 ml) (Type

A) or 5 ounces (150 ml) (Type

B) of GL5 80-90 Weight Gear

Lube. Visco lock (C), fill with

the oil recommended by your

owner’s manual supplment until

oil comes out the plug.

5. Reinstall filler plug.

6. Check for leaks.

Содержание ATV 2002






















































































































































































Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды

Polaris ATV 2002, Руководство пользователя

Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды