Polaris ATV 2002 страница 123 Скачать руководство пользователя

Страница: 123 / 181

120

MAINTENANCE AND LUBRICATION

Lubrication

2x4 Models

To check the level:
1. Remove fill dipstick and

wipe clean.

2. Reinstall dipstick

completely, remove and

check the level. Add the

proper lubricant as

required to bring level

into operating range as

shown.

To change lubricant:
1. Remove skid plate (if

necessary).

2. Place a drain pan beneath

the transmission oil drain plug area.

3. Loosen jam nut (A).
4. Turn adjuster bolt (B) in to allow the removal of drain plug (C).

5. Remove the drain plug and wipe the magnetic end clean to remove

accumulated metallic filings.

6. After the oil has drained completely, install a new sealing washer

and install the drain plug. Torque to 14 ft. lbs. (19.3 Nm).

7. Turn adjuster bolt (B) out until it touches the frame, and then an

additional 1/2 turn.

8. Tighten the jam nut securely while holding the adjuster bolt.

9. Add the proper lubricant through the dipstick hole until the oil

level is between the upper and lower limits. Do not overfill.

10. Check for leaks.

11. Reinstall skid plate if removed in step 1.

Содержание ATV 2002






















































































































































































Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды

Polaris ATV 2002, Руководство пользователя

Результаты поиска

Содержание ATV 2002

Отзывы:

Похожие инструкции для ATV 2002

Бренды по названию

Популярные бренды